- 您現在的位置：買賣IC網 > PDF目錄1908 > CP2103-GMR (Silicon Laboratories Inc)IC CTRLR BRIDGE USB-UART 28MLP PDF資料下載
參數資料
| 型號： | CP2103-GMR |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTRLR BRIDGE USB-UART 28MLP |
| 產品培訓模塊： | CP21xx USB Bridge |
| 標準包裝： | 1,500 |
| 應用： | USB |
| 接口： | USB |
| 電源電壓： | 3 V ~ 3.6 V |
| 封裝/外殼： | 28-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 28-QFN（5x5） |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
| 配用： | 336-1163-ND - KIT EVAL FOR CP2103 USB TO UART |
Rev. 1.0
13
CP2103
4. USB Function Controller and Transceiver
The universal serial bus function controller in the CP2103 is a USB 2.0 compliant full-speed device with integrated
transceiver and on-chip matching and pull-up resistors. The USB function controller manages all data transfers
between the USB and the UART as well as command requests generated by the USB host controller and
commands for controlling the function of the UART.
The USB Suspend and Resume signals are supported for power management of both the CP2103 device as well
as external circuitry. The CP2103 will enter Suspend mode when Suspend signaling is detected on the bus. Upon
entering Suspend mode, the CP2103 asserts the SUSPEND and SUSPEND signals. SUSPEND and SUSPEND
are also asserted after a CP2103 reset until device configuration during USB Enumeration is complete.
The CP2103 exits the Suspend mode when any of the following events occurs: (1) Resume signaling is detected or
generated, (2) a USB Reset signal is detected, or (3) a device reset occurs. Upon exit from Suspend mode, the
SUSPEND and SUSPEND signals are de-asserted.
Both SUSPEND and SUSPEND temporarily float high during a CP2103 reset. If this behavior is undesirable, a
strong pulldown (10 k
) can be used to ensure SUSPEND remains low during reset. See Figure 6 for other
recommended options.
Figure 6. Typical Connection Diagram
Option 1: A 4.7 k
pull-up resistor can be added to increase noise immunity.
Option 2: A 4.7 F capacitor can be added if powering other devices from the on-chip regulator.
Option 3: Avalanche transient voltage suppression diodes should be added for ESD protection .
Option 3: Use Littlefuse p/n SP0503BAHT or equivalent.
Option 4: 10 k
resistor to ground to hold SUSPEND low on initial power on or device reset.
1
CP2103
SUSPEND
11
12
REGIN
7
GND
2
RST
9
D+
3
D-
4
8
C2
0.1
F
C1
1
F
RI
DCD
CTS
RTS
RXD
TXD
DSR
DTR
1
28
27
26
25
24
23
22
2
3
External RS-232
transceiver or
UART circuitry
(to external circuitry
for USB suspend
states)
VBUS
D-
D+
GND 4
5
6
USB
CONNECTOR
6
VDD
VBUS
VDD
R1
4.7 k
D1
D2
D3
Option 1
R2
10 k
Option 4
Option 3
C4
4.7
F
Option 2
VIO
5
1
F
I/O Voltage
GPIO.3
GPIO.2
GPIO.1
GPIO.0
19
18
17
16
External
Application
Circuitry
相關PDF資料 |
PDF描述 |
|---|---|
| CP2104-F03-GM | IC SGL USB-TO-UART BRIDGE 24QFN |
| CP2105-F01-GM | IC SGL USB-DL UART BRIDGE 24QFN |
| CP2112-F01-GM | IC HID USB-TO-SMBUS BRIDGE 24QFN |
| CP2120-GM | IC I/O EXPANDER I2C/SPI 8B 20QFN |
| CP2200-GQ | IC ETH CTRLR SNGL-CHIP 48TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP2104 | 制造商:SILABS 制造商全稱:SILABS 功能描述:USB DRIVER CUSTOMIZATION |
| CP2104EK | 功能描述:界面開發工具 Evaluation kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| CP2104-F03-GM | 功能描述:輸入/輸出控制器接口集成電路 USB to UART bridge RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2104-F03-GMR | 功能描述:輸入/輸出控制器接口集成電路 USB to UART bridge RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2104-MINIEK | 制造商:Silicon Laboratories Inc 功能描述:KIT EVAL FOR CP2104-MINI |
發布緊急采購，3分鐘左右您將得到回復。