- 您現在的位置：買賣IC網 > PDF目錄9492 > CP82C54-12Z (Intersil)IC OSC PROG TIMER 12MHZ 24DIP PDF資料下載
參數資料
| 型號： | CP82C54-12Z |
| 廠商： | Intersil |
| 文件頁數： | 22/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OSC PROG TIMER 12MHZ 24DIP |
| 標準包裝： | 15 |
| 類型： | 可編程計時器 |
| 頻率： | 12MHz |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電流 - 電源： | 10mA |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 24-DIP（0.600"，15.24mm） |
| 包裝： | 管件 |
| 供應商設備封裝： | 24-PDIP |
| 安裝類型： | 通孔 |
| 產品目錄頁面： | 1236 (CN2011-ZH PDF) |
9
82C54
A new initial count may be written to a Counter at any time
without affecting the Counter’s programmed Mode in any way.
Counting will be affected as described in the Mode definitions.
The new count must follow the programmed count format.
If a Counter is programmed to read/write two-byte counts,
the following precaution applies. A program must not
transfer control between writing the first and second byte to
another routine which also writes into that same Counter.
Otherwise, the Counter will be loaded with an incorrect
count.
READ OPERATIONS
It is often desirable to read the value of a Counter without
disturbing the count in progress. This is easily done in the
82C54.
There are three possible methods for reading the Counters.
The first is through the Read-Back command, which is
explained later. The second is a simple read operation of the
Counter, which is selected with the A1, A0 inputs. The only
requirement is that the CLK input of the selected Counter
must be inhibited by using either the GATE input or external
logic. Otherwise, the count may be in process of changing
when it is read, giving an undefined result.
COUNTER LATCH COMMAND
The other method for reading the Counters involves a
special software command called the “Counter Latch
Command”. Like a Control Word, this command is written to
the Control Word Register, which is selected when A1, A0 =
11. Also, like a Control Word, the SC0, SC1 bits select one
of the three Counters, but two other bits, D5 and D4,
distinguish this command from a Control Word.
.
The selected Counter’s output latch (OL) latches the count
when the Counter Latch Command is received. This count is
held in the latch until it is read by the CPU (or until the Counter
is reprogrammed). The count is then unlatched automatically
and the OL returns to “following” the counting element (CE).
This allows reading the contents of the Counters “on the fly”
without affecting counting in progress. Multiple Counter Latch
Commands may be used to latch more than one Counter.
Each latched Counter’s OL holds its count until read. Counter
Latch Commands do not affect the programmed Mode of the
Counter in any way.
If a Counter is latched and then, some time later, latched
again before the count is read, the second Counter Latch
Command is ignored. The count read will be the count at the
time the first Counter Latch Command was issued.
With either method, the count must be read according to the
programmed format; specifically, if the Counter is
programmed for two byte counts, two bytes must be read.
The two bytes do not have to be read one right after the
other; read or write or programming operations of other
Counters may be inserted between them.
Another feature of the 82C54 is that reads and writes of the
same Counter may be interleaved; for example, if the
Counter is programmed for two byte counts, the following
sequence is valid.
1. Read least significant byte.
2. Write new least significant byte.
3. Read most significant byte.
4. Write new most significant byte.
If a counter is programmed to read or write two-byte counts,
the following precaution applies: A program MUST NOT
transfer control between reading the first and second byte to
another routine which also reads from that same Counter.
Otherwise, an incorrect count will be read.
READ-BACK COMMAND
The read-back command allows the user to check the count
value, programmed Mode, and current state of the OUT pin
and Null Count flag of the selected counter(s).
The command is written into the Control Word Register and
has the format shown in Figure 5. The command applies to
POSSIBLE PROGRAMMING SEQUENCE
A1
A0
Control Word - Counter 1
1
Control Word - Counter 0
1
LSB of Count - Counter 1
0
1
Control Word - Counter 2
1
LSB of Count - Counter 0
0
MSB of Count - Counter 1
0
1
LSB of Count - Counter 2
1
0
MSB of Count - Counter 0
0
MSB of Count - Counter 2
1
0
NOTE: In all four examples, all counters are programmed to
Read/Write two-byte counts. These are only four of many
programming sequences.
A1, A0 = 11; CS = 0; RD = 1; WR = 0
D7
D6
D5
D4
D3
D2
D1
D0
SC1
SC0
0
XX
SC1, SC0 - specify counter to be latched
SC1
SC0
COUNTER
00
0
01
1
10
2
1
Read-Back Command
D5, D4 - 00 designates Counter Latch Command, X - Don’t Care.
NOTE: Don’t Care bits (X) should be 0 to insure compatibility
with future products.
相關PDF資料 |
PDF描述 |
|---|---|
| CS82C54-10 | IC OSC PROG TIMER 10MHZ 28PLCC |
| V300A5M300BG2 | CONVERTER MOD DC/DC 5V 300W |
| MS17344R22C22SX | CONN PLUG 4POS STRAIGHT W/SCKT |
| PI3VT34X245BE | IC XLATR BUS SWITCH LV 80-BQSOP |
| D38999/26MJ90SN | CONN PLUG 46POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP82C54R2489 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CP82C54Z | 功能描述:計時器和支持產品 W/ANNEAL PERIPH PRG- CNTR 5V 8MHZ 24PDIP RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| CP82C55A | 功能描述:外圍驅動器與原件 - PCI PERIPH PRG-I/O 5V 8M HZ 40PDIP COM RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| CP82C55A-5 | 功能描述:外圍驅動器與原件 - PCI PERIPH PRG-I/O 5V 5MHZ COM RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| CP82C55A-5S2469 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。