- 您現在的位置：買賣IC網 > PDF目錄1908 > CPC1465M (IXYS Integrated Circuits Division)IC SHDSL/ISDN DC TERM 16MLP PDF資料下載
參數資料
| 型號： | CPC1465M |
| 廠商： | IXYS Integrated Circuits Division |
| 文件頁數： | 2/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SHDSL/ISDN DC TERM 16MLP |
| 標準包裝： | 52 |
| 功能： | DC 信號終端 |
| 接口： | ISDN，SHDSL |
| 電路數： | 1 |
| 功率（瓦特）： | 1W |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WDFN 裸露焊盤 |
| 供應商設備封裝： | 16-MLP（7x6） |
| 包裝： | 管件 |
| 包括： | 光耦合器 |
INTEGRATED CIRCUITS DIVISION
CPC1465
10
www.ixysic.com
R04
2. Functional Description
2.1 Introduction
The CPC1465 can be used for a number of designs
requiring a dc hold circuit such as SHDSL modem and
ISDN NT1 terminal applications. Typical SHDSL
applications will use a circuit design similar to the one
Diagram” on page 9 while the typical ISDN NT1 circuit
design will be similar to the one shown in Figure 10
The DC Termination IC performs two functions in an
ISDN NT1 terminal; as an electronic inductor providing
a low impedance dc termination with a high
impedance ac termination, and second as part of the
dc signalling system for automated line testing
capability. The CPC1465 meets or exceeds the
requirements for an NT1 dc termination as described
in ANSI T1.601-1991.
Whereas the SHDSL modem application does not
have a signalling requirement, the signaling function
provides an excellent method to monitor for the loss of
sealing current. Generally, loss of sealing current in an
SHDSL application indicates loop loss.
As can be seen in the application circuit in Figure 1 on
page 1, CPC1465 designs require few external
components. For the most basic design, all that is
needed is a circuit protector, two resistors and a
capacitor.
2.2 Surge Protection
Although the CPC1465 is current limited, it is not an
over-voltage surge protector. To protect the CPC1465
against destructive over-voltage transients, IXYS
Integrated Circuits Division recommends the use of a
crowbar-type surge protector that limits the surge
voltage seen by the CPC1465 to 250 V. The protection
device must be able to withstand the surge
requirements specified by the appropriate governing
agency in regions where the product will be deployed.
Teccor, Inc. and Bourns, Inc. make suitable surge
protectors for most applications. Devices such as
Teccor’s P1800SC or P2000SC Sidactors and Bourns’
TISP4220H3 or TISP4240H3 thyristors should provide
suitable protection.
2.3 Bridge Rectifier
The bridge rectifier in the CPC1465 ensures that the
device is polarity insensitive and provides consistent
operational characteristics if the tip and ring leads are
reversed.
2.4 State Transitions
The dc tip to ring voltage-current characteristics of the
CPC1465 are shown in Figure 2 “I-V Requirements
Transition timings are illustrated in Figure 7 “Applied
configuration for these timings is given in Figure 6
timing figures are located on page 7.
State transition timings are set by the 1
F capacitor
connected between the TC and COM pins.
2.4.1 Activation - On-State
Application of battery voltage to the loop causes the
CPC1465 to conduct whenever the voltage exceeds
approximately 35 V. With application of sufficient
voltage applied across the tip and ring terminals, the
CPC1465 will initially conduct a nominal 150
A of
sealing current for approximately 20 ms prior to
activation. Once activated, the CPC1465 will remain in
the on state for as long as the loop current exceeds a
nominal 0.5 mA.
The CPC1465 turn-on timing circuit assures device
activation will occur within 50 ms of an applied voltage
greater than 43.5 V but not within the first 3 ms.
2.4.2 Deactivation - Off-State
While the CPC1465 activation protocol is based on an
initial minimum voltage level, deactivation is based on
a diminished sealing current level. Deactivation occurs
when the nominal sealing current level drops below
0.5 mA with guaranteed deactivation occurring for
sealing current levels less than 0.1 mA
相關PDF資料 |
PDF描述 |
|---|---|
| CPC2400E | MODULE MODEM 2400BAUD EMBEDDEDED |
| CPC5601D | IC DRVR PROGRAMMABLE 16-SOIC |
| CPC5710N | IC PHONE LINE MONITOR 8-SOIC |
| CPC5712U | PHONE LINE MON W/DETECTOR 16QSOP |
| CPC7220W | IC ANALOG SWITCH 8CH HV 28-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CPC1465MTR | 功能描述:固態繼電器-PCB安裝 DC Termination IC RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| CPC1466 | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:Broadband ADSL/VDSL DC Termination IC |
| CPC1466D | 功能描述:電信線路管理 IC DC TERMINATION IC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| CPC1466DTR | 功能描述:電信線路管理 IC DC TERMINATION IC, TAPE/REEL RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| CPC1466M | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:Broadband ADSL/VDSL DC Termination IC |
發布緊急采購，3分鐘左右您將得到回復。