INTEGRATED CIRCUITS D
參數資料
型號: CPC2400E
廠商: IXYS Integrated Circuits Division
文件頁數: 17/17頁
文件大小: 0K
描述: MODULE MODEM 2400BAUD EMBEDDEDED
標準包裝: 54
數據格式: V.22,V.23
波特率: 2.4k
電源電壓: 4.75 V ~ 5.25 V
安裝類型: 表面貼裝
封裝/外殼: 模塊
供應商設備封裝: 模塊
INTEGRATED CIRCUITS DIVISION
CPC2400E
www.ixysic.com
9
R03
AT Command Set
Command
Function and Description
&D
Data Terminal &D determines how the modem responds to the DTR signal from the terminal. The country Ready
Options conguration may prevent the modem from detecting terminal DTR. In this case, the modem assumes DTR
is always on. In North America, terminal DTR is normally detected. If DTR detection has been prevented, the modem
will respond with an ERROR result to this command.
The response to changes in DTR also depends on the &Q and &D commands. This table denes what happens
when DTR goes off for all possible combinations of the &D and &Q commands. To see what happens when DTR
goes on refer to the &Q command. The default value is &D0 in North America:
&D0
&D1
&D2
D3
&Q0
None
B
C
D
&Q1
A
B
C
D
A
The modem hangs up the telephone line and issues an OK result code.
B
If in the On-Line state, the modem goes into the Command state and issues an OK result code.
C
The modem hangs up the telephone line and issues an OK result code. Auto-Answer is disabled as
long as DTR stays off.
D
The modem resets.
E
Command Mode E tells the modem whether or not to echo characters sent from the terminal when the modem is
Character Echo accepting AT commands.
E0
Does not echo characters sent from the terminal.
E1
Echo characters sent from the terminal. This is the default value in North America.
%E
Automatic Retrain
Options
The %E command controls whether the modem will initiate retrain with the other modem during a telephone line
connection during operation in data modes supporting retrain. The modem always responds to a retrain operation
initiated by the remote modem. The modem can be forced to initiate a retrain by the On-Line (O1) command.
%E0
Do not initiate a retrain.
%E1
Initiate a retrain if the datapump indicates one is required.
&F
Recall Factory
Prole
&F changes these AT command options and S-registers to their default values. The default values may be changed
for use in different countries. The values for North America are:
S-registers
S0=0 S1=0
S2=43
S3=13
S4=10
S5=8
S6=2 S7=30
S8=2
S9=6
S10=14
S11=95
S12=50
S17=10
S25=5
S28=0
S29=25 S37=0
Commands
B1
E1
M1
P
Q0
V1
X4
&C0
&D0
&G0
&P0
&Q0
%E1
&G
Guard Tone
Options
&G tells the modem which guard tone to transmit when the modem is transmitting the high band (i.e., answer
handshake and answer mode).
&G0
No guard tone. This is the default value in North America.
&G1
550 Hz guard tone (V.22 and V.22bis only)
&G2
1800 Hz guard tone (V.22 and V.22bis only)
相關PDF資料
PDF描述
CPC5601D IC DRVR PROGRAMMABLE 16-SOIC
CPC5710N IC PHONE LINE MONITOR 8-SOIC
CPC5712U PHONE LINE MON W/DETECTOR 16QSOP
CPC7220W IC ANALOG SWITCH 8CH HV 28-PLCC
CPC7232W IC ANALOG SWITCH 8CH HV 28-PLCC
相關代理商/技術參數
參數描述
CPC2400E-EVAL 功能描述:MODULE MODEM 2400BAUD EMBEDDEDED RoHS:否 類別:編程器,開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK(80-QFP ZIF 插口) 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
CPC240J 功能描述:瓷片電容器 CAP DISC 24PF 1000V RoHS:否 制造商:Vishay/Cera-Mite 電容:0.01 uF 容差:20 % 電壓額定值:3 kV 工作溫度范圍:- 25 C to + 105 C 損耗因數 DF: 端接類型:Radial 產品:High Voltage Ceramic Disc Capacitors
CPC242040SC-F 制造商:ebm-papst Inc 功能描述:DCP CONTROLLER 24V 20-40C OC AL 制造商:ebm-papst Inc 功能描述:DCP CONTROLLER 24V, 20-40C OC AL
CPC242040SC-R 制造商:ebm-papst Inc 功能描述:DCP fan controller, 24V OC alarm 20-40C
CPC243555SC-F 制造商:ebm-papst Inc 功能描述:DCP CONTROLLER 24V 35-55OC OC AL 制造商:ebm-papst Inc 功能描述:DCP CONTROLLER 24V, 35-55OC OC AL