- 您現在的位置：買賣IC網 > PDF目錄237314 > CS2320-7EPDDTB2 (POWER-ONE INC) 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | CS2320-7EPDDTB2 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL, CASE S02, MODULE |
| 文件頁數： | 2/33頁 |
| 文件大?。?/td> | 438K |
| 代理商： | CS2320-7EPDDTB2 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
S Series Data Sheet
100 Watt AC-DC and DC-DC Converters
APR 26, 2006 revised to SEP 25, 2006
Page 10 of 33
www.power-one.com
Thermal Considerations
If a converter is located in free, quasi-stationary air (convection
cooling) at the indicated maximum ambient temperature TA max
(see table: Temperature specifications) and is operated at its
nominal input voltage and output power, the temperature
measured at the Measuring point of case temperature TC (see:
Mechanical Data) will approach the indicated value TC max after
the warm-up phase. However, the relationship between TA and
TC depends heavily on the conditions of operation and
integration into a system. The thermal conditions are influenced
by input voltage, output current, airflow and temperature of
surrounding components and surfaces. TA max is therefore,
contrary to TC max, an indicative value only.
Caution: The installer must ensure that under all operating
conditions TC remains within the limits stated in the table
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink allows TA
to be higher than 71
°C (e.g., 85 °C) if TC max is not exceeded.
For -7 or -9 models at ambient temperature TA = 85 °C with only
convection cooling, and the maximum permissible current for each
output is approx. 40% of its nominal value as per the figure below.
Output Protection
Each output is protected against overvoltages which could occur
due to a failure of the internal control circuit. Voltage suppressor
diodes (which under worst case condition may become a short
circuit) provide the required protection. The suppressor diodes are
not designed to withstand externally applied overvoltages.
Overload at any of the outputs will cause a shut-down of all
outputs. A red LED indicates the overload condition.
Parallel or Series Connection
Single or double-output models with equal nominal output voltage
can be connected in parallel without any precautions using
Option T (current sharing).
Single output models and/or main and second outputs of double-
output models can be connected in series with any other (similar)
output.
Notes:
– Parallel connection of double output models should include both,
main and second output to maintain good regulation of both
outputs.
– Not more than 5 models should be connected in parallel.
– Series connection of second outputs without involving their main
outputs should be avoided as regulation may be poor.
– Rated output voltages above 36 V need additional measures in
order to comply with the safety requirements for SELV (Safe Extra
Low Voltage)
– The maximum output current is limited by the output with the lowest
current limitation if several outputs are connected in series.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [C]
0.9
1.0
Forced cooling
05089_052305
TA min
TC max
Convection cooling
Fig. 7
Output current derating versus temperature for -7 and -9
models.
Thermal Protection
A temperature sensor generates an internal inhibit signal which
disables the outputs if the case temperature exceeds TC max.
The outputs are automatically re-enabled when the temperature
drops below this limit.
Continuous operation under simultaneous worst-case conditions
of the following three parameters should be avoided: minimum
input
voltage,
maximum
output
power,
and
maximum
temperature.
Output Voltage Regulation
Fig. 8
Output characteristic Vo1 vs. Io1 (typ.)
Vo
Vo nom
0.98
0.5
0
0.5
1.0
Io1
IoL
Io
Io nom
05098_050605
The following figures apply to single-output or double-output
models with parallel-connected outputs.
相關PDF資料 |
PDF描述 |
|---|---|
| CS2320-7RDDB2 | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| CS2320-9ERD7B2 | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| CS2320-9ERDDTB1 | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| CS2320-9PD3B2 | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| CS2540-7EPD1TB2 | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS2320-7R | 功能描述:EURO-CASSETTE 100W 2X 12V RoHS:否 類別:電源 - 外部/內部（非板載） >> DC DC Converters 系列:* 標準包裝:1 系列:Quint 類型:隔離 輸入電壓:24V 輸出:24V 輸出數:1 輸出 - 1 @ 電流（最大）:24 VDC @ 50A 輸出 - 2 @ 電流（最大）:- 輸出 - 3 @ 電流（最大）:- 輸出 - 4 @ 電流（最大）:- 功率（瓦特）:1200W 安裝類型:底座安裝 工作溫度:0°C ~ 40°C 效率:- 封裝/外殼:模塊 尺寸/尺寸:4.33" L x 9.09" W x 6.14" H（110mm x 231mm x 156mm） 包裝:散裝 電源（瓦特）- 最大:1200W 批準:- 其它名稱:277-69722866365-NDQUINT-BAT/24DC/12AH |
| CS2320-9ER | 制造商:Power-One 功能描述:DCDC - Bulk |
| CS2322 | 制造商:HVPSI 制造商全稱:High Voltage Power Solutions, Inc. 功能描述:HIGH VOLTAGE POWER SUPPLIES |
| CS235 | 制造商:CHERRY 制造商全稱:CHERRY 功能描述:System Photoelectric Smoke Detector |
| CS235/00 | 制造商:Teac 功能描述:5.25" BRACKET FOR THE FD235 制造商:Teac 功能描述:3.5 TO 5.25 KIT - Bulk |
發布緊急采購，3分鐘左右您將得到回復。