- 您現在的位置：買賣IC網 > PDF目錄201423 > CS2843ALN8 (ON SEMICONDUCTOR) 1 A SWITCHING CONTROLLER, PDIP8 PDF資料下載
參數資料
| 型號： | CS2843ALN8 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | 1 A SWITCHING CONTROLLER, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 273K |
| 代理商： | CS2843ALN8 |
CS2842A, CS3842A, CS2843A, CS3843A
http://onsemi.com
6
Figure 4. Test Circuit
VREF
VCC
VOUT
GND
COMP
VFB
Sense
OSC
0.1 μF
RT
1.0 kΩ
1.0 W
2N2222
100 kΩ
VCC
VREF
VOUT
GND
A
5.0 kΩ
Sense
ADJUST
CT
4.7 kΩ
1.0 kΩ
ERROR AMP
ADJUST
CIRCUIT DESCRIPTION
CSX843A
8.4 V
7.6 V
CSX842A
16 V
10 V
VON
VOFF
ON/OFF Command
to reset of IC
VCC
< 1.0 mA
< 15 mA
VON VOFF
VCC
ICC
Figure 5. Typical Undervoltage Characteristics
Undervoltage Lockout
During Undervoltage Lockout (Figure 5), the output
driver is biased to a high impedance state. The output should
be shunted to ground with a resistor to prevent output
leakage current from activating the power switch.
PWM Waveform
To generate the PWM waveform, the control voltage from
the error amplifier is compared to a current sense signal which
represents the peak output inductor current (Figure 6). An
increase in VCC causes the inductor current slope to increase,
thus reducing the duty cycle. This is an inherent feedforward
characteristic of current mode control, since the control
voltage does not have to change during changes of input
supply voltage.
Figure 6. Timing Diagram for Key CS2841B
Parameters
Switch
Current
EA Output
VCC
IO
VO
OSC
RESET
OSC
When the power supply sees a sudden large output current
increase, the control voltage will increase allowing the duty
cycle to momentarily increase. Since the duty cycle tends to
exceed the maximum allowed to prevent transformer
saturation in some power supplies, the internal oscillator
waveform provides the maximum duty cycle clamp as
programmed by the selection of oscillator components.
Setting the Oscillator
Oscillator timing capacitor, CT, is charged by VREF
through RT and discharged by an internal current source.
During the discharge time, the internal clock signal blanks
out the output to the Low state, thus providing a user selected
maximum duty cycle clamp. Charge and discharge times are
determined by the formula:
相關PDF資料 |
PDF描述 |
|---|---|
| CBDPC13W6M0/3W3FR60 | 13 CONTACT(S), MALE-FEMALE, D SUBMINIATURE CONNECTOR, SOLDER |
| CBDPC13W6M0/13W3MR8Z | 13 CONTACT(S), MALE-MALE, D SUBMINIATURE CONNECTOR, SOLDER |
| CA3101E14S-2PNB-06 | 4 CONTACT(S), ALUMINUM ALLOY, MALE, MIL SERIES CONNECTOR, SOLDER, PLUG |
| CA3101E14S-2PNB-32 | 4 CONTACT(S), ALUMINUM ALLOY, MALE, MIL SERIES CONNECTOR, SOLDER, PLUG |
| CA3101E14S-2PXB-32 | 4 CONTACT(S), ALUMINUM ALLOY, MALE, MIL SERIES CONNECTOR, SOLDER, PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS2844 | 制造商:CHERRY 制造商全稱:CHERRY 功能描述:Current Mode PWM Control Circuit with 50% Max Duty Cycle |
| CS-2844 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| CS2844/CS3844/CS2845/CS3845 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current Mode PWM Control Circuit with 50% MAX Duty C |
| CS2844/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current Mode PWM Control Circuit with 50% Max Duty Cycle |
| CS-2844D14 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current-Mode SMPS Controller |
發布緊急采購，3分鐘左右您將得到回復。