- 您現在的位置：買賣IC網 > PDF目錄374166 > CS51221EDR16 (ZF Electronics Corporation) Enhanced Voltage Mode PWM Controller PDF資料下載
參數資料
| 型號： | CS51221EDR16 |
| 廠商： | ZF Electronics Corporation |
| 英文描述： | Enhanced Voltage Mode PWM Controller |
| 中文描述： | 增強的電壓模式PWM控制器 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 164K |
| 代理商： | CS51221EDR16 |
Application Information: continued
8
C
The V
REF
(ok) comparator monitors the 3.3V V
REF
output
and latches a fault condition if V
REF
falls below 3.1V. The
fault condition may also be triggered when the OV pin
voltage rises above 2V or the UV pin voltage falls below
1V. The under-voltage comparator has a built-in hysteresis
of 75mV (typ). The hysteresis for the OV comparator is
programmable through a resistor connected to the OV pin.
When an OV condition is detected, the over-voltage hys-
teresis current of 12.5μA (typ) is sourced from the pin.
In Fig.4, the fault condition is triggered by pulling the UV
pin to the ground. Immediately, the SS capacitor is dis-
charged with 5μA of current (typ) and the GATE output is
disabled until the SS voltage reaches the discharge voltage
of 0.3V (typ). The IC starts the Soft Start transition again if
the fault condition has recovered as shown in Fig.4.
However, if the fault condition persists, the SS voltage will
stay at 0.10V until the removal of the fault condition.
Figure 4: The fault condition is triggered when the UV pin voltage falls
below 1V . The Soft Start capacitor is discharged and the GATE output
is disabled. CH2: Envelop of GATE output, CH3: SS pin with 0.01μF
capacitor, CH4: UV pin.
Current Sense and Over Current Protection
The current can be monitored by the I
SENSE
pin to achieve
pulse by pulse current limit. Various techniques, such as a
using current sense resistor or current transformer, can be
adopted to derive current signals. The voltage of the I
SET
pin sets the threshold for maximum current. As shown in
Fig. 5, when the I
SENSE
pin voltage exceeds the I
SET
voltage,
the current limit comparator will reset the GATE latch flip-
flop to terminate the GATE pulse.
Figure 5: The GATE output is terminated when the I
SENSE
pin voltage
reaches the threshold set by the I
SET
pin. CH2: I
SENSE
SET
pin,
CH3: GATE pin
The current sense signal is prone to leading edge spikes
caused by the switching transition. A RC low-pass filter is
usually applied to the current signals to avoid premature
triggering. However, the low pass filter will inevitably
change the shape of the current pulse and also add cost.
The CS51221uses leading edge blanking circuitry that
blocks out the first 150ns (typ) of each current pulse. This
removes the leading edge spikes without altering the cur-
rent waveform. The blanking is disabled during Soft Start
and when the V
COMP
is saturated high so that the mini-
mum on-time of the controller does not have the additional
blanking period. The max SS detect comparator keeps the
blanking function disabled until SS charges fully. The out-
put of the max Duty Cycle detector goes high when the
error amplifier output gets saturated high, indicating that
the output voltage has fallen well below its regulation
point and the power supply may be under load stress.
Oscillator and Synchronization
The switching frequency is programmable through a RC
network connected to the R
T
C
T
Pin. As shown in Fig.6,
when the R
T
C
T
pin reaches 2V, the capacitor is discharged
by a 1mA current source and the Gate signal is disabled.
When the R
T
C
T
pin decreases to 1V, the Gate output is
turned on and the discharge current is removed to let the
R
T
C
T
pin ramp up. This begins a new switching cycle. The
C
T
charging time over the switch period sets the maximum
duty cycle clamp which is programmable through the R
T
value as shown in the Design Guidelines. At the beginning
of each switching cycle, the SYNC pin generates a 2.5V,
320nS (typ) pulse. This pulse can be utilized to synchronize
other power supplies.
相關PDF資料 |
PDF描述 |
|---|---|
| CS5124 | High Performance, Integrated Current Mode PWM Controllers |
| CS5126XD8 | High Performance, Integrated Current Mode PWM Controllers |
| CS5126 | High Performance, Integrated Current Mode PWM Controllers |
| CS5124XDR8 | High Performance, Integrated Current Mode PWM Controllers |
| CS5126XDR8 | High Performance, Integrated Current Mode PWM Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS51221EDR16G | 功能描述:電壓模式 PWM 控制器 Enhanced Current Mode PWM Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| CS51221EDTB16G | 功能描述:電壓模式 PWM 控制器 ANA PWM CTR TSSOP RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| CS51221EDTB16R2G | 功能描述:電壓模式 PWM 控制器 ANA PWM CTR TSSOP RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| CS51221EN16 | 制造商:CHERRY 制造商全稱:CHERRY 功能描述:Enhanced Voltage Mode PWM Controller |
| CS51227/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Enhanced Voltage Mode PWM Controller |
發布緊急采購，3分鐘左右您將得到回復。