RXD - Receiver Data Output Receiver output data. Normally connected to RxD on the UART. TXD - Transmit Data Input Transmitter input d" />
參數資料
型號: CS8130-CS
廠商: Cirrus Logic Inc
文件頁數: 19/28頁
文件大?。?/td> 0K
描述: IC IR TRANSCEIVER 2-5V 20-SSOP
標準包裝: 66
類型: 收發器
電源電壓: 2.7 V ~ 5.5 V
安裝類型: 表面貼裝
封裝/外殼: 20-SSOP(0.209",5.30mm 寬)
供應商設備封裝: 20-SSOP
包裝: 管件
產品目錄頁面: 758 (CN2011-ZH PDF)
配用: 598-1161-ND - BOARD EVAL FOR CS8130
其它名稱: 598-1203-5
Digital Pins
RXD - Receiver Data Output
Receiver output data. Normally connected to RxD on the UART.
TXD - Transmit Data Input
Transmitter input data. Normally connected to TxD on the UART.
D/C - Data/Control Mode Input
The D/C pin determines whether the input data on TXD is treated as data to be transmitted via
the LED, or as control information to set up the CS8130 internal registers. The D/C pin also
can act as a power down control.
FORM/BSY - Received Data Format Output/Busy Signal Output
If auto format detect mode is enabled, this pin indicates the format of the incoming data.
FORM is low for ASK format data, and high for IRDA/HPSIR format data.
In TV remote data mode (Mode 3), this pin becomes a handshake signal to the UART.
FORM/BSY low means OK to send a character. FORM/BSY high means "I am busy, do not
send another character".
PWRDN - Power Down Control Input
PWRDN low places the CS8130 into a very low power consumption "off" state.
RESET - Reset Input
RESET low places all the internal logic into a known state. All the control register bits are
forced high or low, as defined in the register definition section. If the crystal oscillator is in use,
then RESET must be held low for >25 ms, with PWRDN high and power applied. If an
external clock is used, then the RESET pulse can be short (>1
s).
XTALIN, XTALOUT - Crystal Connections
To use the internal oscillator, connect either a 3.6864 MHz or a 1.8432 MHz crystal between
XTALOUT and XTALIN. If using an external clock, connect XTALIN to DGND.
EXTCLK - External Clock Input or Output
If no crystal is present on XTALIN and XTALOUT, EXTCLK becomes an input. A
3.6864 MHz or 1.8432 MHz clock should be connected to EXTCLK. XTALIN should be
connected to DGND.
If a crystal is present on XTALIN and XTALOUT, EXTCLK becomes an output. EXTCLK will
output the same frequency as the crystal. The EXTCLK output driver may be disabled to
conserve power.
CLKFR - Clock Frequency Select Input
Tie CLKFR to ground to select a 3.6864 MHz clock. Connect CLKFR to the VD+ pin to select
a 1.8432 MHz clock.
CS8130
26
DS134PP2
CS8130
26
DS134F1
相關PDF資料
PDF描述
CS8190EDWF20G IC TACH/SPEEDO DRVR PREC 20SOICW
CS8191XNF16 IC DRVR AIRCORE TACH/SPEED 16DIP
CS82C5296 IC UART/BRG 5V 16MHZ 28-PLCC
CS82C59A-1296 IC CTRL INTERRUPT 12.5MHZ 28PLCC
CS8900A-IQZ IC LAN ETHERNET CTLR 5V 100LQFP
相關代理商/技術參數
參數描述
CS8130-CSR 功能描述:紅外收發器 IC Multi-Standard Infrared Transceiver RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel
CS8130-CSZ 功能描述:紅外收發器 IC Multi-Standard Infrared Transceiver RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel
CS8130-CSZR 功能描述:紅外收發器 IC Multi-Standard Infrared Transceiver RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel
CS8130-IS 制造商:Cirrus Logic 功能描述:IRDA TX/RX 0.1152MBPS 2.7V TO 5.5V 20SSOP - Rail/Tube
CS8130-ISR 制造商:Cirrus Logic 功能描述:IRDA TX/RX 0.1152MBPS 2.7V TO 5.5V 20SSOP - Tape and Reel