- 您現在的位置：買賣IC網 > PDF目錄170212 > CT1995-20 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQIP90 PDF資料下載
參數資料
| 型號： | CT1995-20 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQIP90 |
| 封裝： | 1.600 X 2.400 INCH, CERAMIC, PLUG IN-90 |
| 文件頁數： | 23/27頁 |
| 文件大?。?/td> | 632K |
| 代理商： | CT1995-20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁
5
SCDCT1999 Rev C
and BIT Word contents are controlled by the RT; however the subsystem has the option to set the Message Error
Bit and to control the reset conditions for the Terminal Flag and Subsystem Flag Bits in the Status Word, and the
Transmitter Timeout, Subsystem Handshake, and Loop Test Fail Bits in the BIT Word.
Synchronize Mode Commands
Once the RT has validated the command word and checked for the correct address, the SYNC line is set low. The
signal WC4 will be set low for a Synchronize mode command (See Figure 16), and high for a Synchronize with
data word mode command (See Figure 15). In a Synchronize with data word mode command, SYNC remains low
during the time that the data word is received. Once the data word has been validated, it is passed to the subsystem
on the internal highway IH08-IH715 in two bytes using IUSTB as a strobe signal and H/L as the byte indicator
(high byte first followed by low byte). SYNC being low should be used on the enable to allow IUSTB to clock
synchronize mode data to the subsystem.
If the subsystem does not need to implement either of these mode commands, the SYNC signal can be ignored,
since the RT requires no response from the subsystem.
Transmit Vector Word Mode Command
Figure 14 illustrates the relevant signal timings for an RT receiving a valid Transmit Vector Word mode command.
The RT requests data by setting VECTEN low. The subsystem should use H/L to enable first the high byte and
then the low byte of the Vector word onto the internal highway IH08-IH715.
It should be noted that the RT expects the Vector word contents to be already prepared in a latch ready for enabling
onto the internal highway when VECTEN goes low. If the subsystem has not been designed to handle the Vector
word mode command, it will be the fault of the Bus Controller if the RT receives such a command. Since the
subsystem is not required to acknowledge the mode command, the RT will not be affected in any way by Vector
word circuitry not being implemented in the subsystem. It will however transmit a data word as the Vector word,
but this word will have no meaning.
Reset Mode Command
Figure 8 shows the relevant signal timings for an RT receiving a valid reset mode command. Once the command
word has been fully validated and serviced, the RESET signal is pulsed low. This signal may be used as a reset
function for subsystem interface circuitry.
Dynamic Bus Allocation
This mode command is intended for use with a terminal which has the capability of configuring itself into a bus
controller on command from the bus. The line DBCREQ cannot go true unless the DBCACC line was true at the
time of the valid command, i.e. tied low. For terminals acting only as RTs, the signal DBCACC should be tied
high (inactive), and the signal DBCREQ should be ignored and left unconnected.
Use of the Busy Status Bit
The Busy Bit is used by the subsystem to indicate that it is not ready to handle data transfers either to or from the
RT.
The RT sets the bit to logic one if the BUSY line from the subsystem is active low at the time of the second falling
edge of INCLK after INCMD goes low. This is shown in Figure 13. Once the Busy bit is set, the RT will stop all
receive and transmit data word transfers to and from the subsystem. The data transfers in the Synchronize with
data word and Transmit Vector word mode commands are not affected by the Busy bit and will take place even if
it has been set.
It should be noted that a minimum of 0.5s subaddress decoding time is given to the subsystem before setting of
status bits. This allows the subsystem to selectively set the Busy bit if for instance one subaddress is busy but
others are ready. This option will prove useful when an RT is interfacing with multiple subsystems.
相關PDF資料 |
PDF描述 |
|---|---|
| CT2-GI1LATD53C5 | FIBER OPTIC TRANSCEIVER, 1260-1360nm, 2700Mbps(Tx), 2700Mbps(Rx), PANEL MOUNT, LC CONNECTOR |
| CT2-GI1LATD31C5 | FIBER OPTIC TRANSCEIVER, 1260-1360nm, 2700Mbps(Tx), 2700Mbps(Rx), PANEL MOUNT, LC CONNECTOR |
| CT2-GI1LATD33C4 | FIBER OPTIC TRANSCEIVER, 1260-1360nm, 2700Mbps(Tx), 2700Mbps(Rx), PANEL MOUNT, LC CONNECTOR |
| CT2-GI1LATD51C4 | FIBER OPTIC TRANSCEIVER, 1260-1360nm, 2700Mbps(Tx), 2700Mbps(Rx), PANEL MOUNT, LC CONNECTOR |
| CT2-GI1LATD51C5 | FIBER OPTIC TRANSCEIVER, 1260-1360nm, 2700Mbps(Tx), 2700Mbps(Rx), PANEL MOUNT, LC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CT1995-20-2 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
| CT1995-20-3 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
| CT1999 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT1999 Remote Terminal and/or Bus Controller for MIL-STD-1553B |
| CT1999-FP | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT1999 Remote Terminal and/or Bus Controller for MIL-STD-1553B |
| CT1A18-11PSA206 | 制造商:ITT Interconnect Solutions 功能描述:ER 5C 5#12 PIN RECP |
發布緊急采購，3分鐘左右您將得到回復。