- 您現在的位置：買賣IC網 > PDF目錄237566 > D2F-01L3-D SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.1A, 30VDC, 0.5mm, PANEL MOUNT PDF資料下載
參數資料
| 型號： | D2F-01L3-D |
| 元件分類： | 開關 |
| 英文描述： | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.1A, 30VDC, 0.5mm, PANEL MOUNT |
| 封裝： | ROHS COMPLIANT |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 277K |
| 代理商： | D2F-01L3-D |
D2F
D2F
202
Model
D2F-L2
j
D2F-01L2
j
D2F-FL2
j
D2F-01FL2
j
OF max.
0.78 N {80 gf}
0.39 N {40 gf}
RF min.
{g }
0.05 N {5 gf}
{g }
0.02 N {2 gf}
OT min.
MD max.
0.55 mm
0.5 mm
FP max.
16.5 mm
OP
13
±2 mm
Precautions
Refer to pages 26 to 31 for common precautions.
Cautions
Terminal Connection
When soldering a lead wire to the terminal, first insert the lead wire
conductor into the terminal hole and then perform soldering.
Make sure that the capacity of the soldering iron is 30 W maximum
and that the temperature of the soldering iron tip is approximately
300
°C. (350°C maximum.) Complete the soldering within 3 s.
Using a switch with improper soldering may result in abnormal heat-
ing, possibly resulting in burn.
Applying a soldering iron for more than 3 s or using one that is rated
at more than 30 W may deteriorate the switch characteristics.
When soldering the lead wire to the PCB terminal, pay careful atten-
tion so that the flux and solder liquid level does not exceed the PCB
level.
Correct Use
Mounting
Turn OFF the power supply before mounting or removing the
Switch, wiring, or performing maintenance or inspection. Failure to
do so may result in electric shock or burning.
Use M2 mounting screws with plane washers or spring washers to
securely mount the Switch. Tighten the screws to a torque of 0.08 to
0.1 N
m {0.8 to 1 kgfcm}.
Mount the Switch onto a flat surface. Mounting on an uneven sur-
face may cause deformation of the Switch, resulting in faulty opera-
tion or breakage in the housing.
Operating Stroke Setting
Take particular care in setting the operating stroke for the pin plung-
er models. Make sure that the operating stroke is 70% to 100% of
the rated OT distance. Do not operate the actuator exceeding the
OT distance, otherwise the durability of the Switch may be short-
ened.
Using Micro Loads
Using a model for ordinary loads to open or close the contact of a
micro load circuit may result in faulty contact. Use models that oper-
ate in the following range. However, even when using micro load
models within the operating range shown below, if inrush current oc-
curs when the contact is opened or closed, it may increase contact
wear and so decrease durability. Therefore, insert a contact protec-
tion circuit where necessary.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability lev-
el of 60% (
λ 60). The equation, λ 60 = 0.5 10–6/operations indi-
cates that the estimated malfunction rate is less than 1/2,000,000
operations with a reliability level of 60%.
Operating range
for micro load
models D2F-01
Operating
range for
general-load
models
D2F
Current (mA)
V
oltage
(V)
Inoperable
range
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. B036-E1-07C
Hinge Roller Lever Models
D2F-L2
j
D2F-01L2
j
D2F-FL2
j
D2F-01FL2
j
Note:
Stainless-steel lever
4.8 dia.
× 2.8 (Resin roller)
t = 0.3
(see
note)
(4.6)
OP FP
4
12.8
(10)
4
A
相關PDF資料 |
PDF描述 |
|---|---|
| DC1ES1SC | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 1A, 48VDC, 6.5mm, PANEL MOUNT |
| DC1BM5SB | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 1A, 48VDC, 6mm, PANEL MOUNT |
| DC1CM6RC | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 1A, 48VDC, 6.5mm, THROUGH HOLE-RIGHT ANGLE |
| DC1BS1RC | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 1A, 48VDC, 6.5mm, PANEL MOUNT |
| DC1CC1AA | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 1A, 48VDC, 1.6mm, THROUGH HOLE-STRAIGHT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| D2F01L3-D | 制造商:Omron Corporation 功能描述:SUBMINIATURE BASIC SWITCH |
| D2F01L3D2 | 制造商:Omron Electronic Components LLC 功能描述:SUBMINIATURE BASIC SWITCH - Trays 制造商:Omron Electronic Components LLC 功能描述:DETECTION SWITCHES SUBMINIATURE BASIC SWITCH |
| D2F-01L3-D2 | 功能描述:基本/快動開關 Subminiature Basic Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
| D2F01L3D3 | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT SIMULATED ER LVR SLDR 3A 125VAC 30VDC 0.7 - Trays 制造商:Omron Electronic Components LLC 功能描述:SUBMINIATURE BASIC SWITCH |
| D2F-01L3-D3 | 功能描述:基本/快動開關 Subminiature Basic Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
發布緊急采購，3分鐘左右您將得到回復。