參數資料
型號: D372A
廠商: Electronic Theatre Controls, Inc.
英文描述: Electroluminescent Lamp Driver IC
中文描述: 電致發光燈驅動IC
文件頁數: 4/12頁
文件大?。?/td> 448K
代理商: D372A
4
Theory of Operation
Electroluminescent (EL) lamps are essentially capacitors with one transparent electrode and a special phosphor material
in the dielectric. When a strong AC voltage is applied across the EL lamp electrodes, the phosphor glows. The
required AC voltage is typically not present in most systems and must be generated from a low voltage DC source.
The D372 chip inverter drives the EL lamp by using a switching BJT to repeatedly charge an external inductor and
discharge it to the high voltage capacitor Cs. The discharging causes the voltage at Cs to continually increase. When
the voltage at Cs reaches a nominal value, the switching BJT is turned off. The internal circuitry uses the H-bridge
technology, using both electrodes to drive the EL lamp. One of the outputs, EL1 or EL2, is used to discharge Cs into the
EL lamp during the first half of the low frequency (LF) cycle. By alternating the state of the H-bridge, the other output
is used to charge the EL lamp during the second half of the LF cycle. The alternating states make it possible to achieve
200V peak-to-peak across the EL lamp.
The EL driving system is divided into several parts: on-chip logic control, on-chip high voltage output circuitry, on-chip
discharge logic circuitry, and off-chip components. The on-chip logic controls the lamp operating frequency (LF) and
the inductor switching frequency (HF). These signals are used to drive the high voltage output circuitry (H-bridge) by
delivering the power from the inductor to the lamp. The integrated discharge logic circuitry uses a patented wave
shaping technique for reducing audible noise from an EL lamp. Changing the Rd value changes the slope of the linear
discharge as well as the shape of the waveform. The off-chip component selection provides a degree of flexibility to
accommodate various lamp sizes, system voltages, and brightness levels.
Typical D372 EL driving configurations for driving EL lamps in various applications are shown on the following page.
The expected system outputs for the various circuit configurations are also shown with each respective figure. These
examples are only guides for configuring the driver. Durel provides a D372 Designers Kit, which includes a printed
circuit evaluation board intended to aid you in developing an EL lamp driver configuration using the D372 that meets
your requirements. A section on designing with the D372 is included in this datasheet to serve as a guide to help you
select the appropriate external components to complete your D372 EL driver system.
Block Diagram of the Driver Circuitry
EL Lamp
E
V+
L+
GND
EL1
High
Frequency
Oscillator
CHF
Low
Frequency
Oscillator
CLF
R
d
V
BAT
L
o
g
i
c
L
o
g
i
c
Divide
by 2
EL2
C
S
相關PDF資料
PDF描述
D372 Digital Uncooled DFB(distributed-feedback) Laser Module for 2.5 Gbits/s Applications(在傳輸速率為2.5G位/秒領域中應用的數字常溫DFB(分布式反饋)激光模塊)
D374-10A D374-Type Digital Uncooled 2.5 Gbits/s Laser Module
D374-02A D374-Type Digital Uncooled 2.5 Gbits/s Laser Module
D374-02F D374-Type Digital Uncooled 2.5 Gbits/s Laser Module
D374-02N D374-Type Digital Uncooled 2.5 Gbits/s Laser Module
相關代理商/技術參數
參數描述
D-373 制造商:Triad Magnetics 功能描述:
D37349-000 制造商:TE Connectivity 功能描述:NC-381381-2.5-9 - Bag 制造商:TE Connectivity 功能描述:LABEL ID PRODUCT 制造商:TE Connectivity 功能描述:Labels Thermal Transfer Printable Label Nylon Cloth White 38.1x38.1mm
D37354-000 制造商:TE Connectivity 功能描述:PVF190319WE2.5 - Cable Rools/Shrink Tubing 制造商:TE Connectivity 功能描述:LABEL ID PRODUCT 制造商:TE Connectivity 功能描述:Labels Thermal Transfer Printable Label Translucent Polyvinyl Fluoride White 48.3x81mm
D37375 制造商:Sprague/Vishay 功能描述:SPRAGUE TWISTLOK SKID 6A
D373S E373S WAF 制造商:Fairchild Semiconductor Corporation 功能描述: