- 您現在的位置：買賣IC網 > PDF目錄376558 > DAC6571EVM (Texas Instruments, Inc.) DAC6571 Evaluation Module(DAC6571評估模塊) PDF資料下載
參數資料
| 型號： | DAC6571EVM |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | DAC6571 Evaluation Module(DAC6571評估模塊) |
| 中文描述： | DAC6571評估模塊（DAC6571評估模塊） |
| 文件頁數： | 16/39頁 |
| 文件大?。?/td> | 437K |
| 代理商： | DAC6571EVM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
PCB Layout
2-2
2.1
PCB Layout
The DAC EVM demonstrates the high performance of the DAC under test
conditions specified in the datasheet by implementing design practices that
preserve DAC performance. Careful analysis of these practices is the key to
a successful design implementation. Many of the practices affect the
schematic design phase, including correct component selection, adequate
bypassing, separating and managing analog and digital signals, and
understanding component mechanical attributes.
The circuit layout is critical in any high-performance analog circuit, and DAC
circuit design is no exception. Component placement and signal routing are
important considerations. Place bypass capacitors as close as possible to the
pins, with analog and digital signals properly separated from each other.
The power and ground planes are very important and must be carefully
designed. A solid plane is best, but when solid planes are not possible, a split
plane is usually adequate. When considering a split plane design, analyze the
component placement and carefully divide the board into its analog and digital
sections starting from the device under test. The ground plane plays an
important role in controlling the noise and other effects that contribute to DAC
output errors. To ensure that return currents are handled properly, route the
signals only in their respective sections; analog traces must only lie directly
above or below the analog section and digital traces in the digital section.
Minimize the length of the traces but use the widest allowable trace in the
design. The EVM layout incorporates these design practices and are shown
in the illustrations presented below.
This DAC EVM board is constructed on a four-layer printed circuit board using
a copper-clad FR-4 laminate material. The printed circuit board dimensions
are 43,1800 mm (1.7000 inch)
×
82,5500 mm (3.2500 inch), and the board
thickness is 1,5748 mm (0.0620 inch). Figure 2-1 through Figure 2-7 shows
the artwork for the individual layers.
Figure 2-1. Top Silkscreen
相關PDF資料 |
PDF描述 |
|---|---|
| DAC7571EVM | DAC7571 Evaluation Module(DAC7571評估模塊) |
| DAC56 | Monolithic 16-Bit Resolution DIGITAL-TO-ANALOG CONVERTER |
| DAC600 | 12-Bit 256MHz Monolithic DIGITAL-TO-ANALOG CONVERTER |
| DAC600 | 12-Bit 256MHz Monolithic Dightal-To-Analog Converter(12位 256MHz單片D/A轉換器) |
| DAC650 | 12-Bit 500MHz DIGITAL-TO-ANALOG CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC6571IDBVR | 功能描述:數模轉換器- DAC DAC6571: 10-Bit RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC6571IDBVRG4 | 功能描述:數模轉換器- DAC DAC6571: 10-Bit RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC6571IDBVT | 功能描述:數模轉換器- DAC DAC6571: 10-Bit RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC6571IDBVT | 制造商:Texas Instruments 功能描述:IC 10BIT DAC SMD 6571 SOT-23-6 |
| DAC6571IDBVTG4 | 功能描述:數模轉換器- DAC DAC6571: 10-Bit RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。