- 您現在的位置：買賣IC網 > PDF目錄9032 > DAC7621EB (Texas Instruments)IC 12-BIT D/A PARALLEL 20-SSOP PDF資料下載
參數資料
| 型號： | DAC7621EB |
| 廠商： | Texas Instruments |
| 文件頁數： | 3/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 12-BIT D/A PARALLEL 20-SSOP |
| 產品培訓模塊： | Data Converter Basics |
| 標準包裝： | 70 |
| 設置時間： | 7µs |
| 位數： | 12 |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 5mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
| 輸出數目和類型： | 1 電壓，單極 |
| 采樣率（每秒）： | 143k |
| 產品目錄頁面： | 899 (CN2011-ZH PDF) |
11
DAC7621
FIGURE 4. Suggested Power and Ground Connections for a DAC7621 Sharing a +5V Supply with a Digital System with a
Single Ground Plane.
APPLICATIONS
POWER AND GROUNDING
The DAC7621 can be used in a wide variety of situations—
from low power, battery operated systems to large-scale
industrial process control systems. In addition, some appli-
cations require better performance than others, or are par-
ticularly sensitive to one or two specific parameters. This
diversity makes it difficult to define definite rules to follow
concerning the power supply, bypassing, and grounding.
The following discussion must be considered in relation to
the desired performance and needs of the particular system.
A precision analog component requires careful layout, ad-
equate bypassing, and a clean, well-regulated power supply.
As the DAC7621 is a single-supply, +5V component, it will
often be used in conjunction with digital logic,
microcontrollers, microprocessors, and digital signal proces-
sors. The more digital logic present in the design and the
higher the switching speed, the more difficult it will be to
achieve good performance.
The DAC7621 has separate analog ground and digital ground
pins. The current through DGND is mostly switching tran-
sients and are up to 4mA peak in amplitude. The current
through AGND is typically 0.5mA.
For best performance, separate analog and digital ground
planes with a single interconnection point to minimize
ground loops. The analog pins are located adjacent to each
other to help isolate analog from digital signals. Analog
signals should be routed as far as possible from digital
signals and should cross them at right angles. A solid analog
ground plane around the D/A package, as well as under it in
the vicinity of the analog and power supply pins, will isolate
the D/A from switching currents. It is recommended that
DGND and AGND be connected directly to the ground
planes under the package.
If several DAC7621s are used, or if sharing supplies with
other components, connecting the AGND and DGND lines
together at the power supplies once, rather than at each chip,
may produce better results.
The power applied to VDD should be well regulated and low-
noise. Switching power supplies and DC/DC converters will
often have high-frequency glitches or spikes riding on the
output voltage. In addition, digital components can create
similar high frequency spikes as their internal logic switches
states. This noise can easily couple into the DAC output
voltage through various paths between VDD and VOUT.
As with the GND connection, VDD should be connected to
a +5V power supply plane or trace that is separate from the
connection for digital logic until they are connected at the
power entry point. In addition, the 10
F and 0.1F capaci-
tors shown in Figure 4 are strongly recommended and
should be installed as close to VDD and ground as possible.
In some situations, additional bypassing may be required
such as a 100
F electrolytic capacitor or even a “Pi” filter
made up of inductors and capacitors—all designed to essen-
tially lowpass filter the +5V supply, removing the high
frequency noise (see Figure 4).
+
+5V
GND
100
F
Digital Circuits
+5V
GND
+5V
Power
Supply
Other
Analog
Components
V
DD
AGND
DGND
DAC7621
+
10
F
0.1
F
Optional
相關PDF資料 |
PDF描述 |
|---|---|
| MS27474T24B29S | CONN RCPT 29POS JAM NUT W/SCKT |
| VI-B3X-MV-F3 | CONVERTER MOD DC/DC 5.2V 150W |
| MS3454W10SL-3P | CONN RCPT 3POS JAM NUT W/PINS |
| MS3454L10SL-3P | CONN RCPT 3POS JAM NUT W/PINS |
| D38999/20MJ61PB | CONN RCPT 61POS WALL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC7621EB | 制造商:Texas Instruments 功能描述:Digital-Analog Converter IC Interface Ty |
| DAC7621EB/1K | 功能描述:數模轉換器- DAC 12-Bit Para Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC7621EB/1KG4 | 功能描述:數模轉換器- DAC 12B Parallel Input DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC7621EBG4 | 功能描述:數模轉換器- DAC 12-Bit Para Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC7621EG4 | 功能描述:數模轉換器- DAC 12-Bit Para Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。