參數資料
型號: DC1145B
廠商: Linear Technology
文件頁數: 3/32頁
文件大?。?/td> 0K
描述: EVAL BOARD FOR LTC4267
設計資源: DC1145B Design Files
標準包裝: 1
主要目的: 電源管理,以太網供電(POE)
嵌入式:
已用 IC / 零件: LTC4267
已供物品:
LTC4267
11
4267fc
Series Diodes
The IEEE 802.3af-dened operating modes for a PD refer-
ence the input voltage at the RJ45 connector on the PD.
The PD must be able to accept power of either polarity
at each of its inputs, so it is common to install diode
bridges (Figure 2). The LTC4267 takes this into account
by compensating for these diode drops in the threshold
points for each range of operation. A similar adjustment
is made for the UVLO voltages.
Detection
During detection, the PSE will apply a voltage in the
range of – 2.8V to –10V on the cable and look for a 25kΩ
signature resistor. This identies the device at the end of
the cable as a PD. With the terminal voltage in this range,
the LTC4267 connects an internal 25kΩ resistor between
the VPORTP and VPORTN pins. This precision, temperature
compensated resistor presents the proper signature to
alert the PSE that a PD is present and desires power to be
applied. The internal low-leakage UVLO switch prevents
the switching regulator circuitry from affecting the detec-
tion signature.
The LTC4267 is designed to compensate for the voltage
and resistance effects of the IEEE required diode bridge.
The signature range extends below the IEEE range to ac-
commodate the voltage drop of the two diodes. The IEEE
specication requires the PSE to use a ΔV/ΔI measurement
technique to keep the DC offset of these diodes from af-
fecting the signature resistance measurement. However,
the diode resistance appears in series with the signature
resistor and must be included in the overall signature
resistance of the PD. The LTC4267 compensates for the
two series diodes in the signature path by offsetting the
resistance so that a PD built using the LTC4267 will meet
the IEEE specication.
In some applications it is necessary to control whether or
not the PD is detected. In this case, the 25kΩ signature
resistor can be enabled and disabled with the use of the
SIGDISA pin (Figure 3). Disabling the signature via the
SIGDISA pin will change the signature resistor to 9kΩ
(typical) which is an invalid signature per the IEEE 802.3af
specication. This invalid signature is present for PD input
voltages from –2.8V to –10V. If the input rises above –10V,
the signature resistor reverts to 25kΩ to minimize power
dissipation in the LTC4267. To disable the signature, tie
SIGDISA to VPORTP. Alternately, the SIGDISA pin can be
driven high with respect to VPORTN. When SIGDISA is high,
all functions of the PD interface are disabled.
APPLICATIO S I FOR ATIO
WU
UU
RX
6
RX+
3
TX
2
TX+
RJ45
T1
POWERED DEVICE (PD)
INTERFACE
AS DEFINED
BY IEEE 802.3af
4267 F02
1
7
8
5
4
SPARE
SPARE+
TO PHY
BR2
BR1
VPORTP
8
4
D3
LTC4267
VPORTN
Figure 2. LTC4267 PD Front End Using
Diode Bridges on Main and Spare Inputs
相關PDF資料
PDF描述
6-1676941-0 INDUCTOR 33UH 2.5A SMD
RCC17DRYH CONN EDGECARD 34POS DIP .100 SLD
VE-B2W-EW CONVERTER MOD DC/DC 5.5V 100W
HCC10DRTN CONN EDGECARD 20POS DIP .100 SLD
V110C36C100B CONVERTER MOD DC/DC 36V 100W
相關代理商/技術參數
參數描述
DC1149D17XX-D4X WAF 制造商:Fairchild Semiconductor Corporation 功能描述:
DC1149E25XX-D4X WAF 制造商:Fairchild Semiconductor Corporation 功能描述:
DC1149E29XX_D4X WAF 制造商:Fairchild Semiconductor Corporation 功能描述:
DC114R 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
DC115 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC