參數資料
型號: DC1369A-H
廠商: Linear Technology
文件頁數: 19/34頁
文件大?。?/td> 0K
描述: BOARD DEMO 105MSPS LTC2260-12
軟件下載: QuikEval II System
設計資源: DC1369A Design Files
標準包裝: 1
系列: *
相關產品: DC890B-ND - BOARD USB DATA COLLECTION
LTC2261-12
LTC2260-12/LTC2259-12
26
226112fc
For more information www.linear.com/LTC2261-12
applicaTions inForMaTion
Serial Programming Mode
To use the serial programming mode, PAR/SER should be
tied to ground. The CS, SCK, SDI and SDO pins become a
serialinterfacethatprogramtheA/Dmodecontrolregisters.
Data is written to a register with a 16-bit serial word. Data
can also be read back from a register to verify its contents.
Serial data transfer starts when CS is taken low. The data
on the SDI pin is latched at the first 16 rising edges of
SCK. Any SCK rising edges after the first 16 are ignored.
The data transfer ends when CS is taken high again.
The first bit of the 16-bit input word is the R/W bit. The
next seven bits are the address of the register (A6:A0).
The final eight bits are the register data (D7:D0).
If the R/W bit is low, the serial data (D7:D0) will be writ-
ten to the register set by the address bits (A6:A0). If the
R/W bit is high, data in the register set by the address bits
(A6:A0) will be read back on the SDO pin (see the timing
diagrams). During a read back command the register is
not updated and data on SDI is ignored.
The SDO pin is an open-drain output that pulls to ground
with a 200 impedance. If register data is read back
through SDO, an external 2k pull-up resistor is required. If
serial data is only written and read back is not needed, then
SDO can be left floating and no pull-up resistor is needed.
Table 3 shows a map of the mode control registers.
Software Reset
If serial programming is used, the mode control registers
shouldbeprogrammedassoonaspossibleafterthepower
supplies turn on and are stable. The first serial command
must be a software reset which will reset all register data
bits to logic 0. To perform a software reset, bit D7 in the
reset register is written with a logic 1. After the reset SPI
write command is complete, bit D7 is automatically set
back to zero.
Table 3. Serial Programming Mode Register Map
REGISTER A0: RESET REGISTER (ADDRESS 00h)
D7
D6
D5
D4
D3
D2
D1
D0
RESET
X
Bit 7
RESET
Software Reset Bit
0 = Not Used
1 = Software Reset. All Mode Control Registers are Reset to 00h. This Bit is Automatically Set Back to Zero at the End of the SPI Write
Command.
The Reset Register Is Write Only.
Bits 6-0
Unused, Don’t Care Bits.
REGISTER A1: POWER-DOWN REGISTER (ADDRESS 01h)
D7
D6
D5
D4
D3
D2
D1
D0
X
PWROFF1
PWROFF0
Bits 7-2
Unused, Don’t Care Bits.
Bits 1-0
PWROFF1:PWROFF0
Power Down Control Bits
00 = Normal Operation
01 = Nap Mode
10 = Not Used
11 = Sleep Mode
相關PDF資料
PDF描述
CM381 LAMP T1-3/4 FLANGE BASE .2A
A0213Y 30MM IND CTRL PB OPERATOR
CM380 LAMP T1-3/4 FLANGE BASE .04A
194- LAMP T3-1/4 WEDGE BASE
7220 LAMP INCAND T-1 STD WIRE TERM
相關代理商/技術參數
參數描述
DC1369A-I 功能描述:BOARD DEMO 80MSPS LTC2259-12 RoHS:是 類別:未定義的類別 >> 其它 系列:* 標準包裝:1 系列:* 其它名稱:MS305720A
DC1369A-J 制造商:Linear Technology 功能描述:12BIT ADC Eval Brd, Rq. DC1371 & DC1075 制造商:Linear Technology 功能描述:12BIT ADC Eval Brd, Rq. DC1371 & DC1075; Silicon Manufacturer:Linear Technology; Silicon Core Number:LTC2258-12; Kit Application Type:Data Converter; Application Sub Type:ADC; Kit Contents:Board, Guide
DC1369A-K 制造商:Linear Technology 功能描述:12BIT ADC Eval Brd, Rq. DC1371 & DC1075 制造商:Linear Technology 功能描述:12BIT ADC Eval Brd, Rq. DC1371 & DC1075; Silicon Manufacturer:Linear Technology; Silicon Core Number:LTC2257-12; Kit Application Type:Data Converter; Application Sub Type:ADC; Kit Contents:Board, Guide
DC1369A-L 制造商:Linear Technology 功能描述:12BIT ADC Eval Brd, Rq. DC1371 & DC1075 制造商:Linear Technology 功能描述:12BIT ADC Eval Brd, Rq. DC1371 & DC1075; Silicon Manufacturer:Linear Technology; Silicon Core Number:LTC2256-12; Kit Application Type:Data Converter; Application Sub Type:ADC; Kit Contents:Board, Guide
DC1369A-M 制造商:Linear Technology 功能描述:BOARD DEMO 150MSPS LTC2262-14 制造商:Linear Technology 功能描述:14BIT ADC Eval Brd, Rq. DC1371 & DC1075 制造商:Linear Technology 功能描述:14BIT ADC Eval Brd, Rq. DC1371 & DC1075; Silicon Manufacturer:Linear Technology; Silicon Core Number:LTC2262-14; Kit Application Type:Data Converter; Application Sub Type:ADC; Kit Contents:Board, Guide