參數資料
型號: DC1783A-H
廠商: Linear Technology
文件頁數: 3/24頁
文件大?。?/td> 0K
描述: BOARD SAR ADC LTC2376-18
軟件下載: QuikEval II System
設計資源: DC1783A Design Files
DC1783A Schematic
標準包裝: 1
系列: QuikEval™
ADC 的數量: 1
位數: 18
采樣率(每秒): 250k
數據接口: 串行,SPI?
輸入范圍: ±VREF
在以下條件下的電源(標準): 3.4mW @ 250kSPS
工作溫度: 0°C ~ 70°C
已用 IC / 零件: LTC2376-18
已供物品:
相關產品: LTC2376IDE-16#TRPBF-ND - IC ADC 16BIT SPI 250KSPS 16DFN
LTC2376IDE-16#PBF-ND - IC ADC 16BIT SPI 250KSPS 16DFN
LTC2376HMS-16#TRPBF-ND - IC ADC 16BIT SPI 250KSPS 16MSOP
LTC2376HMS-16#PBF-ND - IC ADC 16BIT SPI 250KSPS 16MSOP
LTC2376CDE-16#TRPBF-ND - IC ADC 16BIT SPI 250KSPS 16DFN
LTC2376CDE-16#PBF-ND - IC ADC 16BIT SPI 250KSPS 16DFN
LTC2376IMS-16#TRPBF-ND - IC ADC 16BIT 250KSPS 16-MSOP
LTC2376CMS-16#TRPBF-ND - IC ADC 16BIT 250KSPS 16-MSOP
LTC2376IMS-16#PBF-ND - IC ADC 16BIT 250KSPS 16-MSOP
LTC2376CMS-16#PBF-ND - IC ADC 16BIT 250KSPS 16-MSOP
更多...
LTC2376-18
11
237618f
APPLICATIONS INFORMATION
INPUT DRIVE CIRCUITS
A low impedance source can directly drive the high im-
pedance inputs of the LTC2376-18 without gain error. A
high impedance source should be buffered to minimize
settling time during acquisition and to optimize the dis-
tortion performance of the ADC. Minimizing settling time
is important even for DC inputs, because the ADC inputs
draw a current spike when entering acquisition.
For best performance, a buffer amplifier should be used
to drive the analog inputs of the LTC2376-18. The ampli-
fier provides low output impedance, which produces fast
settling of the analog signal during the acquisition phase.
It also provides isolation between the signal source and
the current spike the ADC inputs draw.
Input Filtering
The noise and distortion of the buffer amplifier and signal
source must be considered since they add to the ADC noise
and distortion. Noisy input signals should be filtered prior
to the buffer amplifier input with an appropriate filter to
minimize noise. The simple 1-pole RC lowpass filter (LPF1)
shown in Figure 4 is sufficient for many applications.
20Ω
3300pF
6600pF
20Ω
500Ω
LPF2
LPF1
BW = 600kHz
BW = 48kHz
SINGLE-ENDED-
TO-DIFFERENTIAL
DRIVER
SINGLE-ENDED-
INPUT SIGNAL
LTC2376-18
IN+
IN
237618 F04
6800pF
High quality capacitors and resistors should be used in the
RC filters since these components can add distortion. NPO
and silver mica type dielectric capacitors have excellent
linearity. Carbon surface mount resistors can generate
distortion from self heating and from damage that may
occur during soldering. Metal film surface mount resistors
are much less susceptible to both problems.
Single-Ended-to-Differential Conversion
For single-ended input signals, a single-ended to differential
conversion circuit must be used to produce a differential
signal at the inputs of the LTC2376-18. The LT6350 ADC
driver is recommended for performing single-ended-to-
differential conversions. The LT6350 is flexible and may
be configured to convert single-ended signals of various
amplitudes to the ±5V differential input range of the
LTC2376-18. The LT6350 is also available in H-grade to
complement the extended temperature operation of the
LTC2376-18 up to 125°C.
Figure 5a shows the LT6350 being used to convert a 0V
to 5V single-ended input signal. In this case, the first
amplifier is configured as a unity gain buffer and the single-
ended input signal directly drives the high-impedance
input of the amplifier. As shown in the FFT of Figure 5b,
the LT6350 drives the LTC2376-18 to near full data sheet
performance.
The LT6350 can also be used to buffer and convert large
true bipolar signals which swing below ground to the
±5V differential input range of the LTC2376-18 in order
to maximize the signal swing that can be digitized. Fig-
ure6a shows the LT6350 being used to convert a ±10V
true bipolar signal for use by the LTC2376-18. In this
case, the first amplifier in the LT6350 is configured as
an inverting amplifier stage, which acts to attenuate and
level shift the input signal to the 0V to 5V input range of
the LTC2376-18. In the inverting amplifier configuration,
the single-ended input signal source no longer directly
drives a high impedance input of the first amplifier. The
input impedance is instead set by resistor RIN. RIN must
be chosen carefully based on the source impedance of the
signal source. Higher values of RIN tend to degrade both
the noise and distortion of the LT6350 and LTC2376-18
as a system.
Figure 4. Input Signal Chain
Another filter network consisting of LPF2 should be used
between the buffer and ADC input to both minimize the
noise contribution of the buffer and to help minimize distur-
bances reflected into the buffer from sampling transients.
Long RC time constants at the analog inputs will slow
down the settling of the analog inputs. Therefore, LPF2
requires a wider bandwidth than LPF1. A buffer amplifier
with a low noise density must be selected to minimize
degradation of the SNR.
相關PDF資料
PDF描述
ESM10DREH CONN EDGECARD 20POS .156 EYELET
0210490947 CABLE JUMPER 1.25MM .076M 25POS
NR8040T680M INDUCTOR 68UH 1.1A 20% SMD
VE-B5T-EY CONVERTER MOD DC/DC 6.5V 50W
EMM10DREH CONN EDGECARD 20POS .156 EYELET
相關代理商/技術參數
參數描述
DC1785A 功能描述:BOARD DEMO LTC2991 RoHS:是 類別:編程器,開發系統 >> 評估板 - 傳感器 系列:QuikEval™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
DC1785A 制造商:Linear Technology 功能描述:EVAL BOARD, LTC2991 TEMP, VOLTAGE, CURRE
DC1786A 功能描述:BOARD DEMO LTC2871 RoHS:是 類別:編程器,開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信,線路接口單元(LIU) 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板,電源,線纜,CD 其它名稱:82EBV2081
DC1788A-B 制造商:Linear Technology 功能描述:EVAL BOARD, LT4275B POE & PD CONTROLLER, Silicon Manufacturer:Linear Technology,
DC1788A-C 制造商:Linear Technology 功能描述:EVAL BOARD, LT4275C POE & PD CONTROLLER, Silicon Manufacturer:Linear Technology,