- 您現在的位置：買賣IC網 > PDF目錄298985 > DCW1033 DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | DCW1033 |
| 元件分類： | 電源模塊 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 封裝： | PLASTIC, SIP-7/8 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 245K |
| 代理商： | DCW1033 |
5
Design & Feature Considerations
Maximum Capacitive Load
The DCW1000 series has limitation of maximum
connected capacitance at the output. The power
module may be operated in current limiting mode
during start-up, affecting the ramp-up and the startup
time.
Output Ripple Reduction
A good quality low ESR capacitor placed as close as
practicable across the load will give the best ripple and
noise performance.
To reduce output ripple, it is recommended to use
3.3uF capacitors at the output.
+Out
-Out
+Vin
-Vin
Load
DC Power
Source
+
-
Cout
Single Output
DC / DC
Converter
Remote On/Off
The DCW1000 has nagetive remote on/off logic.
Negative logic remote on/off turns the module on during
a logic low voltage on the remote on/off pin, and off
during a logic high.
Remote on/off can be controlled by an external switch
between the on/off terminal and the -Vin terminal. The
switch can be an open collector or equivalent.
Vo(+)
Vo(-)
Vi(+)
Vi(-)
ON/OFF
Overcurrent Protection
To provide protection in a fault (output overload) condition,
the unit is equipped with internal current limiting circuitry
and can endure current limiting for an unlimited duration.
At the point of current-limit inception, the unit shifts from
voltage control to current control. The unit operates
normally once the output current is brought back into its
specified range.
Soldering and Cleaning Considerations
Post solder cleaning is usually the final board assembly
process before the board or system undergoes electrical
testing. Inadequate cleaning and/or drying may lower the
reliability of a power module and severely affect the
finished circuit board assembly test. Adequate cleaning
and/or drying is especially important for un-encapsulated
and/or open frame type power modules. For assistance
on appropriate soldering and cleaning procedures,
please contact Delta’s technical support team.
Notes:
1. These power converters require a minimum output load
to maintain specified regulation (please see page 6 for
the suggested minimum load). Operation under no-load
conditions will not damage these modules; however,
they may not meet all specifications listed above.
2. These DC/DC converters should be externally fused at
the front end for protection.
ON/OFF
相關PDF資料 |
PDF描述 |
|---|---|
| DCW1042 | DC-DC REG PWR SUPPLY MODULE |
| DC | POLYCARBONATE, FEMALE; MALE, CIRCULAR CONNECTOR, CRIMP; SOLDER, PLUG; RECEPTACLE |
| DD105N8K | 105 A, 800 V, SILICON, RECTIFIER DIODE |
| DD175N30K-A | 223 A, 3000 V, SILICON, RECTIFIER DIODE |
| DD76N12L | 76 A, 1200 V, SILICON, RECTIFIER DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DCW12 | 制造商:MEANWELL 制造商全稱:Mean Well Enterprises Co., Ltd. 功能描述:12W DC-DC Regulated Dual Output Converter |
| DCW12/12/1700 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DCW12/12D/500 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DCW12/15/1500 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DCW12/15D/400 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。