參數資料
型號： DEIC420
廠商： IXYS CORP
元件分類： MOSFETs
英文描述： 20 Ampere Low-Side Ultrafast RF MOSFET Driver
中文描述： 20 A BUF OR INV BASED MOSFET DRIVER, PDFP6
封裝： DE275-6
文件頁數： 7/7頁
文件大?。?/td> 156K
代理商： DEIC420
7
DEIC420
APPLICATIONS INFORMATION
High Frequency Gate Drive Circuit
The circuit diagram in figure 17 is a circuit diagram for a
very high switching speed, high frequency gate driver
circuit using the DEIC420. This is the circuit used in the
EVIC420 Evaluation Board,and is capable of driving a
MOSFET at up to the maximum operating limits of the
DEIC420. The circuit's very high switching speed and
high frequency operation dictates the close attention to
several important issues with respect to circuit design.
The three key elements are circuit loop inductance, Vcc
bypassing and grounding.
Circuit Loop Inductance
Referring to Figure 17, the Vcc to Vcc ground current
path defines the loop which will generate the inductive
term. This loop must be kept as short as possible. The
output lead must be no further than 0.375 inches
(9.5mm) from the gate of the MOSFET. Furthermore the
output ground leads must provide a balanced symmetric
coplanar ground return for optimum operation.
Vcc Bypassing
In order for the circuit to turn the MOSFET on properly,
the DEIC420 must be able to draw up to 20A of current
from the Vcc power supply in 2-6ns (depending upon the
input capacitance of the MOSFET being driven). This
means that there must be very low impedance between
the driver and the power supply. The most common
method of achieving this low impedance is to bypass the
power supply at the driver with a capacitance value that
is at least two orders of magnitude larger than the load
capacitance. Usually, this is achieved by placing two or
three different types of bypassing capacitors, with
complementary impedance curves, very close to the
driver itself. (These capacitors should be carefully
selected, low inductance, low resistance, high-pulse
current-service capacitors). Care should be taken to
keep the lengths of the leads between these bypass
capacitors and the DEIC420 to an absolute minimum.
The bypassing should be comprised of several values of
chip capacitors symmetrically placed on ether side of
the IC. Recommended values are .01uF, .47uF chips
and at least two 4.7uF tantalums.
Grounding
In order for the design to turn the load off properly, the
DEIC420 must be able to drain this 20A of current into
an adequate grounding system. There are three paths for
returning current that need to be considered: Path #1 is
between the DEIC420 and its load. Path #2 is between
the DEIC420 and its power supply. Path #3 is between
the DEIC420 and whatever logic is driving it. All three of
these paths should be as low in resistance and
inductance as possible, and thus as short as practical.
Output Lead Inductance
Of equal importance to supply bypassing and grounding
are issues related to the output lead inductance. Every
effort should be made to keep the leads between the
driver and its load as short and wide as possible, and
treated as coplanar transmission lines.
In configurations where the optimum configuration of
circuit layout and bypassing cannot be used, a series
resistance of a few Ohms in the gate lead may be
necessary to prevent ringing.
Heat Sinking
For high power operation, the bottom side metalized
substrate should be placed in compression against an
appropriate heat sink. The substrate is metalized for
improved heat dissipation, and is not electrically
connected to the device or to ground.
See the DEI technical note "DE-Series MOSFET and IC
Mounting Instructions" on the DEI web site at
mounting instructions. The package dimensions of the
相關PDF資料
PDF描述
DELAY EM56/57 - Speech & Music Synthesizer - Application Note - Application Note
DEM-ACF2101BP DEM-ACF2101BP - DISCONTINUED PRODUCT. No longer recommended for new design.
DEM-ADS83XE DEM-ADS83xE - EVALUTION FIXTURE
DEM-ADS9XXE DEM-ADS9xxE - EVALUATION FIXTURE
DEM-ADS1210 DEM-ADS1210 - Evaluation Fixture
相關代理商/技術參數
參數描述
DEIC421 功能描述:RF MOSFET DRIVER 20 AMP RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:高端 輸入類型:非反相 延遲時間:200ns 電流 - 峰:250mA 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:600V 電源電壓:12 V ~ 20 V 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-DIP 包裝:管件 其它名稱:*IR2127
DEIC515 制造商:IXYS Corporation 功能描述:IC DRIVER MOSFET DE150 制造商:IXYS Corporation 功能描述:IC, DRIVER, MOSFET DE150 制造商:IXYS Corporation 功能描述:IC, RF MOSFET DRIVER LOW SIDE DE150IC-10, Device Type:MOSFET, Module Configuration:Low Side, Peak Output Current:15A, Supply Voltage Min:8V, Supply Voltage Max:30V, Driver Case Style:DE150-IC, No. of Pins:10, Input Delay:17.4ns , RoHS Compliant: Yes
DEID2470JA5N00 制造商:KEMET Corporation 功能描述:SMT FILM CAP 2220 0.047UF 250V T5 5% H2.3 L6.3 - Tape and Reel
DEID3100JA0N00 制造商:KEMET Corporation 功能描述:SMT FILM CAP 2220 100NF 250V T5 5% H4.1 L5.7 - Tape and Reel
DEID3100KA0N00 制造商:KEMET Corporation 功能描述:Cap Film 0.1uF 250V PEN 10% (6 X 5 X 4.1mm) SMD 125 制造商:KEMET Corporation 功能描述:SMT FILM CAP,2220,100NF,250V,T5.1,H4.1,L5.7,TR,HAZMAT - Tape and Reel 制造商:KEMET Corporation 功能描述:CAP FILM 0.1UF 250VDC 2220
發布緊急采購，3分鐘左右您將得到回復。