- 您現在的位置：買賣IC網 > PDF目錄368022 > DIC01D724AV0 PDF資料下載
參數資料
| 型號： | DIC01D724AV0 |
| 文件頁數： | 2/5頁 |
| 文件大?。?/td> | 216K |
| 代理商： | DIC01D724AV0 |
2
Specifications are subject to change without notice (21.10.00)
DIC01, PIC01
Mode of Operation
DIC01 and PIC01 monitor
both AC and DC current and
voltage. DIC01 can also
monitor positive and nega-
tive DC voltage connecting
terminals Y1 and Z3.
Example 1
(no contact input - under+over
voltage - 2 x SPDT N.D. relays
(1 x SPDT for PIC01) - TRMS)
DIC01:
One relay operates
when the voltage drops below
the under voltage set point
for more than the respective
delay time. It releases when
the voltage exceeds the set
level plus the set hysteresis.
The other relay operates
when the voltage exceeds
the over voltage set point for
more than the respective
delay time. It releases when
the voltage drops below the
set level minus hysteresis.
PIC01:
The relay operates
when the voltage drops below
the under voltage set level
for more than the respective
set delay time or when it
exceeds the over voltage set
level for more than the rela-
tive set delay time. The relay
releases when the voltage
exceeds the under voltage
set level plus hysteresis and
Power supply
Rated operational voltage
through terminals:
A1, A2 or A3, A2 (DIC01)
2, 10 or 11, 10 (PIC01)
Overvoltage cat. III
(IEC 60664, IEC 60038)
724:
B48:
24 VDC ± 20%, insulated
24/48 VAC ± 15%
45 to 65 Hz, insulated
115/230 VAC ± 15%
45 to 65 Hz, insulated
B23:
Supply Specifications
Power ON delay
Reaction time
1 s ± 0.5 s or 6 s ± 0.5 s
(input signal variation from
-20% to +20% or from
+20% to -20% of set value)
< 100 ms
< 100 ms
(15 min warm-up time)
± 1000 ppm/°C
± 10% on set value ± 50 ms
± 0.5% on full-scale
Alarm ON delay
Alarm OFF delay
Accuracy
Temperature drift
Delay ON alarm
Repeatability
Indication for
Power supply ON
Alarm ON
LED, green
LED, red (flashing 2 Hz
during delay time)
1 or 2 x LED(s), yellow
Output relay ON
General Specifications
Output
Rated insulation voltage
Contact ratings
(AgSnO
)
Resistive loads
1 or 2 x SPDT relays
250 VAC
μ
8 A @ 250 VAC
5 A @ 24 VDC
2.5 A @ 250 VAC
2.5 A @ 24 VDC
≥
30 x 10
6
operations
≥
10
5
operations
(at 8 A, 250 V, cos
= 1)
≤
7200 operations/h
AC 1
DC 12
Small inductive loads AC 15
DC 13
Mechanical life
Electrical life
Operating frequency
Dielectric strength
Dielectric voltage
Rated impulse withstand volt. 4 kV (1.2/50 μs)
≥
2 kVAC (rms)
Output Specifications
Environment
Degree of protection
Pollution degree
Operating temperature
Storage temperature
Housing dimensions
Din-rail version
Plug-in version
Weight
Screw terminals
Tightening torque
(EN 60529)
IP 20
3 (DIC01), 2 (PIC01)
-20 to 60°C, R.H. < 95%
-30 to 80°C, R.H. < 95%
45 x 80 x 99.5 mm
36 x 80 x 87 mm
Approx. 250 g
Max. 0.5 Nm
acc. to IEC 60947
Yes
CE-Marking
Note:
MP 3... current transformers
not suitable for under current
measurements due to the
output signal of the device
(see data sheet)
Contact input
DIC01
PIC01
Disabled
Enabled
Latch disable
Terminals Z1, Y1
Terminals 8, 9
> 10 k
< 500
> 500 ms
Input Specifications (cont.)
Dielectric voltage
Supply to input
Supply to output
Input to output
Rated operational power
AC
DC
DC supply
2 kV
4 kV
4 kV
AC supply
4 kV
4 kV
4 kV
5 VA
3 W
相關PDF資料 |
PDF描述 |
|---|---|
| DIC01DB23AV0 | |
| DIC01DB48AV0 | |
| PIC01CB23AV0 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| PIC01CB48AV0 | |
| PIC10F200(中文) | 6-Pin, 8-Bit Flash Microcontrollers(6引腳，8位FLASH微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DIC01D748AV0 | 制造商:Carlo Gavazzi 功能描述:48 VDC PROCESS SIGNAL RLY |
| DIC01DB23AV0 | 制造商:Carlo Gavazzi 功能描述:PROCESS SIGNAL RELAY |
| DIC01DD48AV0 | 制造商:Carlo Gavazzi 功能描述:24-48V PROCESS SIGNAL RLY |
| DIC-1005-1 | 制造商: 功能描述: 制造商:ITT Interconnect Solutions 功能描述: 制造商:undefined 功能描述: |
| DIC121000 | 制造商:COSMO 制造商全稱:COSMO Electronics Corporation 功能描述:Outside Dimension |
發布緊急采購，3分鐘左右您將得到回復。