- 您現在的位置：買賣IC網 > PDF目錄223656 > DIW5029 DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | DIW5029 |
| 元件分類： | 電源模塊 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 封裝： | DIP-8/23 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 273K |
| 代理商： | DIW5029 |
5
Design & Feature Considerations
Maximum Capacitive Load
The DIW5000 series has limitation of maximum
connected capacitance at the output. The power
module may be operated in current limiting mode
during start-up, affecting the ramp-up and the startup
time.
Output Ripple Reduction
A good quality low ESR capacitor placed as close as
practicable across the load will give the best ripple and
noise performance.
To reduce output ripple, it is recommended to use
3.3uF capacitors at the output.
+Out
-Out
+Vin
-Vin
Load
DC Power
Source
+
-
Cout
Single Output
DC / DC
Converter
+Out
-Out
+Vin
-Vin
Load
DC Power
Source
+
-
Cout
Com.
Dual Output
DC / DC
Converter
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal current
limiting circuitry and can endure current limiting for an
unlimited duration. At the point of current-limit
inception, the unit shifts from voltage control to current
control. The unit operates normally once the output
current is brought back into its specified range.
Over voltage Protection
The output over voltage clamp control is independent of
the primary regulation loop. It monitors the voltage on
the output terminals. The control loop of the clamp has
a higher voltage set point than the primary loop. This
provides a redundant voltage control that reduces the
risk of output over voltage.
Soldering and Cleaning Considerations
Post solder cleaning is usually the final board assembly
process before the board or system undergoes electrical
testing. Inadequate cleaning and/or drying may lower the
reliability of a power module and severely affect the
finished circuit board assembly test. Adequate cleaning
and/or drying is especially important for un-encapsulated
and/or open frame type power modules. For assistance
on appropriate soldering and cleaning procedures,
please contact Delta’s technical support team.
Notes:
1. These power converters require a minimum output load
to maintain specified regulation (please see page 6 for
the suggested minimum load). Operation under no-load
conditions will not damage these modules; however,
they may not meet all specifications listed above.
2. These DC/DC converters should be externally fused at
the front end for protection.
相關PDF資料 |
PDF描述 |
|---|---|
| DJ1GARAO | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 2A, 12VDC, THROUGH HOLE-RIGHT ANGLE |
| DK-621-0411-P | CABLE TERMINATED, MALE, TRIAXIAL CONNECTOR, SOLDER, PLUG |
| DK-621-0411-S | CABLE TERMINATED, FEMALE, TRIAXIAL CONNECTOR, SOLDER, PLUG |
| DK-621-0412-P | CABLE TERMINATED, MALE, TRIAXIAL CONNECTOR, SOLDER, JACK |
| DK-621-0412-S | CABLE TERMINATED, FEMALE, TRIAXIAL CONNECTOR, SOLDER, JACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DIW6 7321000 | 制造商:Belden Inc 功能描述:CAT3 6PR U/UTP CMR REEL |
| DIX4192 | 制造商:BB 制造商全稱:BB 功能描述:Integrated Digital Audio Interface Receiver and Transmitter |
| DIX4192EVM-PDK | 功能描述:音頻 IC 開發工具 DIG AUDIO INTERFACE RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| DIX4192IPFB | 功能描述:音頻發送器、接收器、收發器 Dig Aud Interface Xceiver RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
| DIX4192IPFBG4 | 功能描述:音頻發送器、接收器、收發器 Dig Aud Interface Xceiver RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
發布緊急采購，3分鐘左右您將得到回復。