- 您現在的位置：買賣IC網 > PDF目錄376722 > DJIXELAD0SE000 (Intel Corp.) Advanced 8-Port 10/100 Mbps PHY Transceivers PDF資料下載
參數資料
| 型號： | DJIXELAD0SE000 |
| 廠商： | Intel Corp. |
| 英文描述： | Advanced 8-Port 10/100 Mbps PHY Transceivers |
| 中文描述： | 先進的8端口10/100 Mbps的物理層收發器 |
| 文件頁數： | 163/226頁 |
| 文件大?。?/td> | 1575K |
| 代理商： | DJIXELAD0SE000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁當前第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁
LXT9785 and LXT9785E Advanced 8-Port 10/100 Mbps PHY Transceivers
Datasheet
Document Number: 249241
Revision Number: 007
Revision Date: August 28, 2003
165
Intel recommends filtering the power supply to the analog VCC pins of the LXT9785/LXT9785E.
This has two benefits. First, it keeps digital switching noise out of the analog circuitry inside the
LXT9785/LXT9785E, helping with line performance. Second, if the VCC planes are laid out
correctly, digital switching noise is kept away from external connectors, reducing EMI problems.
The recommended implementation is to break the VCC plane into two sections. The digital section
supplies power to the VCCD and VCCIO pins of the LXT9785/LXT9785E. The analog section
supplies power to the VCCA pins. The break between the two planes should run underneath the
device. In designs with more than one the LXT9785/LXT9785E, a single continuous analog VCC
plane can be used to supply them all.
The digital and analog VCC planes should be joined at one or more points by ferrite beads. The
beads should produce at least a 100
impedance at 100 MHz. Beads should be placed so that
current flow is evenly distributed. The maximum current rating of the beads should be at least
150% of the current that is actually expected to flow through them. A bulk cap (2.2 -10
μ
F) should
be placed on each side of each bead.
In addition, a high-frequency bypass cap (0.01
μ
F) should be placed near each analog VCC pin.
5.2.2
Power and Ground Plane Layout Considerations
Great care needs to be taken when laying out the power and ground planes.
Follow the guidelines in the
LXT9785 Design and Layout Guide (formerly Application Note
151)
for locating the split between the digital and analog VCC planes.
Keep the digital VCC plane away from the TPFOP/N and TPFIP/N signals, the magnetics, and
the RJ-45 connectors.
Place the layers so that the TPFOP/N and TFPIP/N signals can be routed near or next to the
ground plane. For EMI reasons, it is more important to shield TPFOP/N than TPFIP/N.
5.2.2.1
Chassis Ground
For ESD reasons, it is a good design practice to create a separate chassis ground that encircles the
board and is isolated via moats and keep-out areas from all circuit-ground planes and active
signals. Chassis ground should extend from the RJ-45 connectors to the magnetics, and can be used
to terminate unused signal pairs (Bob Smith termination). In single-point grounding applications,
provide a single connection between chassis and circuit grounds with a 2 kV isolation capacitor. In
multi-point grounding schemes (chassis and circuit grounds joined at multiple points), provide
2 kV isolation to the Bob Smith termination.
5.2.3
MII Terminations
Series termination resistors are required on all the SS-SMII output signals driven by the LXT9785/
LXT9785E. Special trace layout consideration should be used when using the SMII interface. Keep
all traces orthogonal and as short as possible. Whenever possible, route the clock and sync traces
evenly between the longest and shortest data routes. This minimizes round-trip, clock-to-data
delays and allows a larger margin to the setup and hold requirements.
5.2.4
Twisted-Pair Interface
Use the following standard guidelines for a twisted-pair interface:
相關PDF資料 |
PDF描述 |
|---|---|
| DJIXELAD0SE001 | Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXELCD0QE001 | Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXELCD0SE000 | Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXELCD0SE001 | Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXELED0QE000 | Advanced 8-Port 10/100 Mbps PHY Transceivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DJIXELAD0SE001 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXELCD0QE000 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXELCD0QE001 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXELCD0SE000 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXELCD0SE001 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 8-Port 10/100 Mbps PHY Transceivers |
發布緊急采購，3分鐘左右您將得到回復。