- 您現在的位置：買賣IC網 > PDF目錄376722 > DJIXFLCD0QE000 (Intel Corp.) Advanced 8-Port 10/100 Mbps PHY Transceivers PDF資料下載
參數資料
| 型號： | DJIXFLCD0QE000 |
| 廠商： | Intel Corp. |
| 英文描述： | Advanced 8-Port 10/100 Mbps PHY Transceivers |
| 中文描述： | 先進的8端口10/100 Mbps的物理層收發器 |
| 文件頁數： | 160/226頁 |
| 文件大?。?/td> | 1575K |
| 代理商： | DJIXFLCD0QE000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁當前第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁
LXT9785 and LXT9785E Advanced 8-Port 10/100 Mbps PHY Transceivers
162
Datasheet
Document Number: 249241
Revision Number: 007
Revision Date: August 28, 2003
3. Poll Register bit 29.9. When this bit is set, the test is complete and Register bits 29.7:0 contain
a value used to determine if a cable fault was found and the distance to that fault. A value of
0xFFh indicates no fault was found. Any other value indicates a fault was found, that value
should be stored for later use.
4. Write 0x6C00h to Register 29. Setting these bits places the device in long cable Cable
Diagnostics mode.
5. Poll Register bit 29.9. When set, record the value of Register bits 29.7:0 if a fault is found.
6. If a fault is present, a calculation is used to determine the distance to the fault. Insert the
smallest value recorded from Register bits 29.7:0 in steps 3 and 5 above into the following
formula:
Distance_to_Fault = (Reg29[7:0] - 3.5) / 1.16
Register bit 29.8 is set if the fault is detected as a short circuit and is cleared if the fault is
detected as an open circuit. Register bits 29.12:11 are cleared when read and are cleared during
the same read cycle when Register bit 29.9 is read, indicating a fault condition exists.
7. Normal PHY operation can be resumed by writing 0x4000h to Register 29 or by software or
hardware reset. The test suite can be run again by resuming at step 2 above.
4.14
Link Hold-Off Overview
The PHY link is established as soon as the system platform powers-up. In many cases, the system
platform is not capable of supporting network operation until configuration firmware is loaded. It is
desirable in such cases to prevent the PHY from establishing a link until the system platform is
fully configured and ready for network operation. Link Hold-Off was incorporated into the
LXT9785 device to satisfy these requirements. Enabling Link Hold-Off disables the PHY Link
capability until the system platform is fully capable of supporting network operation. The feature is
enabled by hardware control at power-up or software control during normal operation.
4.14.1
Features
Link Hold-Off prevents the LXT9785 from establishing a link by disabling the analog transmit and
receive capability. The digital capabilities of the PHY are unaffected including register access and
LED operation. Link Hold-Off can be enabled by an external hardware pin for all ports or by
software register access for individual ports. When Link Hold-Off is enabled, the transmitter and
receiver on the selected ports are forced into software power-down mode (see
Section 4.5.3,
“Power-Down Mode” on page 127
) to block signal activity from establishing a link and passing
packets through the PHY.
The hardware enabled Link Hold-Off is controlled by the LINKHOLD pin. Internal pull-down
resistors hold the pin in the inactive state. Connecting a 5k pull-up resistor to the pin enables the
feature at power-up reset or external hardware pin Reset. Once a PHY port is programmed as
desired, clearing Register bit 0.11 will re-enable that port. Each port must be individually re-
enabled.
When a port is software reset, by setting Register 0.15, the state of the hardware configuration pin
captured by the last hardware or power-up reset determines the default register values for the
specific function for that port. Link Hold-Off, once enabled by hardware configuration, is re-
enabled on a port by issuing a software reset for that port. It is not necessary to reset the entire PHY
or switch system to re-enable Link Hold-Off.
相關PDF資料 |
PDF描述 |
|---|---|
| DJIXFLCD0QE001 | Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXFLCD0SE000 | Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXFLCD0SE001 | Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXFLED0QE000 | Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXFLED0QE001 | Advanced 8-Port 10/100 Mbps PHY Transceivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DJIXFLCD0QE001 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXFLCD0SE000 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXFLCD0SE001 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXFLED0QE000 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 8-Port 10/100 Mbps PHY Transceivers |
| DJIXFLED0QE001 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 8-Port 10/100 Mbps PHY Transceivers |
發布緊急采購，3分鐘左右您將得到回復。