- 您現在的位置：買賣IC網 > PDF目錄376727 > DKF110PFWLPES (Fujitsu Limited) Solid-State Fingerprint Sensor PDF資料下載
參數資料
| 型號： | DKF110PFWLPES |
| 廠商： | Fujitsu Limited |
| 英文描述： | Solid-State Fingerprint Sensor |
| 中文描述： | 固態指紋傳感器 |
| 文件頁數： | 6/24頁 |
| 文件大?。?/td> | 240K |
| 代理商： | DKF110PFWLPES |
Peimnay
Solid-State Fingerprint Sensor
2
Fujitsu Microelectronics, Inc.
After the row capture is completed, the High-Order Column Address
Register (CAH) and Low-Order Column Address Register (CAL)
must be programmed to select an element within the captured row to
be digitized. Writing to CAL causes the analog-to-digital (A/D)
converter to digitize the difference between the outputs of the two
sample-and-holds of the selected column cell. The output of the A/D
converter is accessed by reading the CAL register.
Rows can be accessed in any order; however, the selected row must be
captured before the column cells are read. The column cells within a
row can be accessed in any order.
Special Features
There are two programmable open-drain outputs that can be used
for driving LEDs.
The CLKOUT pin can be enabled to output a square-wave clock of
the same frequency as the oscillator clock. CLKOUT can be used to
drive external circuitry. When ENCLK is high, the clock signal is
present at the CLKOUT pin. When ENCLK is low or unconnected,
the CLKOUT output is held low.
MBF110 Pin Information for SOP (VSPA) 80/1
Pin
Number
Pin
Name
Type
Description
Notes
34
A3
Input
Address Inputs
Address signals connected to these pins select a register to read from or write to dur-
ing data transfer.
35
A2
36
A1
37
A0
38
CE1
Chip Enable, Active Low
When CE1 is low and CE2 is high, the chip is selected.
39
CE2
Chip Enable, Active High
When CE1 is low and CE2 is high, the chip is selected.
40
RD
Read Enable, Active Low
This pin must be low while WR is high and the chip selected in order to read a register
on the chip.
17
WR
Write Enable, Active Low
This pin must be low while the chip is selected to write to a register on the chip.
18
D7
Bi-directional
Data Bus
Inputs when WR is low and chip is selected. Outputs when RD is low, WR is high, and
chip is selected.
19
D6
21
D5
22
D4
24
D3
25
D2
26
D1
27
D0
32
CLKOUT
Output
Clock Output
This pin outputs the oscillator clock frequency when ENCLK is high.
31
ENCLK
Input
Enable Clock Output
A high on this pin enables the CLKOUT pin. A low on this pin holds CLKOUT low.
ENCLK has an internal pull-down resistor.
15
LED1
Open-drain
Output
LED driver
This pin can be used to drive an LED.
14
LED2
Open-drain
Output
3
SETCUR
Input
Set Discharge Current
Place an external resistor R1 (200K – 680K ohms) between this pin and ground.
Typical: FPS110, R1 = 680K; FPS110B, R1 = 200K; FPS110E, R1 = 200K
2
N/A
Reserved pin
Must be left disconnected.
13
TEST
20, 33
V
DD
Power
Digital Power Supply
1
V
DDA
Analog Power Supply
相關PDF資料 |
PDF描述 |
|---|---|
| DKF110PFWLPG | Solid-State Fingerprint Sensor |
| DKF110PFWSTES | Solid-State Fingerprint Sensor |
| DKF110PFWSTG | Solid-State Fingerprint Sensor |
| DKWP40 | DKWP40 - Hallotron sygna硂wy |
| DKWP60 | DKWP60 - Hallotron sygna硂wy |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DKF110PFWLPG | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Solid-State Fingerprint Sensor |
| DKF110PFWSTES | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Solid-State Fingerprint Sensor |
| DKF110PFWSTG | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Solid-State Fingerprint Sensor |
| DKF20310 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:NTC Diode Thermometrics Thermistors |
| DKF2032 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:NTC Diode Thermometrics Thermistors |
發布緊急采購，3分鐘左右您將得到回復。