- 您現在的位置：買賣IC網 > PDF目錄376738 > DLG2416 (SIEMENS A G) 4-Character 5x7 Dot Matrix Alphanumeric IntelligentDisplay with Memory/Decoder/Driver PDF資料下載
參數資料
| 型號： | DLG2416 |
| 廠商： | SIEMENS A G |
| 元件分類： | 顯示用LED |
| 英文描述： | 4-Character 5x7 Dot Matrix Alphanumeric IntelligentDisplay with Memory/Decoder/Driver |
| 中文描述： | 5X7 DOT MATRIX DISPLAY, GREEN, 5.08 mm |
| 文件頁數： | 4/7頁 |
| 文件大?。?/td> | 214K |
| 代理商： | DLG2416 |
5–4
DLR/DLO/DLG2416
Loading Data
Setting the chip enable (CE1, CE2) to their true state will enable
data loading. The desired data code (D0-D6) and digit address
(A0, A1) must be held stable during the write cycle for storing
new data.
Data entry may be asynchronous and random. Digit 0 is
defined as right hand digit with A1=A2=0.`
To clear the entire internal four-digit memory hold the clear
(CLR) low for 1
μ
s. All illuminated dots will be turned off within
one complete display multiplex cycle, 1 msec minimum. The
clear function will clear both the ASCII RAM and the cursor
RAM.
Setting the chip enables (CE1, CE2) and cursor select (CU) to
their true state will enable cursor loading. A write (WR) pulse
will now store or remove a cursor into the digit location
addressed by A0, A1, as defined in data entry. A cursor will be
stored if D0=1 and will removed if D0=0. The cursor (CU) pulse
width should not be less than the write (WR) pulse or erroneous
data may appear in the display.
If the cursor is not required, the cursor enable signal (CUE)
may be tied low to disable the cursor function. For a flashing
cursor, simply pulse CUE. If the cursor has been loaded to any
or all positions in the display, then CUE will control whether the
cursor(s) or the characters will appear. CUE does not affect the
contents of cursor memory.
Loading Cursor
Setting the chip enables (CE1, CE2) and cursor select (CU) to
their true state will enable cursor loading. A write (WR) pulse
will now store or remove a cursor into the digit location
addressed by A0, A1, as defined in data entry. A cursor will be
stored if D0=1 and will removed if D0=0. The cursor (CU) pulse
width should not be less than the write (WR) pulse or erroneous
data may appear in the display.
If the cursor is not required, the cursor enable signal (CUE)
may be tied low to disable the cursor function. For a flashing
cursor, simply pulse CUE. If the cursor has been loaded to any
or all positions in the display, then CUE will control whether the
cursor(s) or the characters will appear. CUE does not affect the
contents of cursor memory.
Display Blanking
Blanking the display may be accomplished by loading a blank
or space into each digit of the display or by using the (BL) dis-
play blank input.
Setting the (BL) input low does not affect the contents of either
data or cursor memory.
A flashing circuit can easily be constructed using a 555 astable
multivibrator. Figure 3 illustrates a circuit in which varying R2
(100K~10K) will have a flash rate of 1 Hz~10 Hz.
The display can be dimmed by pulse width modulating the
(BL) at a frequency sufficiently fast to not interfere with the
internal clock. The dimming signal frequency should be 2.5
KHz or higher. Dimming the display also reduces power con-
sumption.
An example of a simple dimming circuit using a 556 is illus-
trated in Figure 4. Adjusting potentiometer R3 will dim the dis-
play by changing the blanking pulse duty cycle.
Figure 3. DLX2416—Flashing circuit using a 555
and Flashing (Blanking) timing
Figure 4. DLX2416Dimming circuit using a 556
and Dimming (Blanking) timing
555
Timer
R1
4.7 K
R2
100 K
C4
0.01
μ
F
C3
10
μ
F
VCC=5.0 V
To BL
Pin on
Display
1
2
3
4
8
7
6
5
Blanking Pulse Width
≈
50% Duty Factor
500 ms
~
2 Hz Blanking Frequency
1
0
~
1
0
200
μ
s
~
Blanking Pulse Width
4
μ
s min., 196
μ
s max.
5 KHz Blanking Frequency
~
C3
1000 pF
1
2
3
4
5
6
7
14
13
12
11
10
9
8
556
Dual Timer
R2
47 K
R1
200
C1
4700 pF
C4
0.01
μ
F
R3
500 K
VCC=5.0 V
Dimming (Blanking)
Control
C2
0.01
μ
F
To BL Pin
on Display
相關PDF資料 |
PDF描述 |
|---|---|
| DLR2416 | 4-Character 5x7 Dot Matrix Alphanumeric IntelligentDisplay with Memory/Decoder/Driver |
| DLO2416 | 4-Character 5x7 Dot Matrix Alphanumeric IntelligentDisplay with Memory/Decoder/Driver |
| DLG4137 | 43/68 Single Character DLO4135/7 5x7 Dot Matrix Intelligent Display |
| DLG7137 | 43/68 Single Character DLO4135/7 5x7 Dot Matrix Intelligent Display |
| DLO7135 | 43/68 Single Character DLO4135/7 5x7 Dot Matrix Intelligent Display |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DLG3416 | 功能描述:LED 顯示器和配件 5x7 Green 0.27", 4-CHARACTER RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| DLG4137 | 功能描述:LED 顯示器和配件 5x7 Green 0.43", 1-CHARACTER RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| DLG50PS12 | 制造商:XP Power 功能描述:LED DRIVER AC-DC 50W 制造商:XP Power 功能描述:LED DRIVER, AC-DC, 50W 制造商:XP Power 功能描述:LED DRIVER, 12VDC, 50W; Applications:Lighting; Power Supply Output Type:Fixed; Input Voltage VAC:90V to 305V; No. of Outputs:1; Output Voltage Nom.:12V; Output Current Max:4.2A; Output Power Max:50W; Depth:39mm; Width:68mm ;RoHS Compliant: Yes |
| DLG50PS24 | 制造商:XP Power 功能描述:LED DRIVER AC-DC 50W 制造商:XP Power 功能描述:LED DRIVER, 24VDC, 50W; Applications:Lighting; Power Supply Output Type:Fixed; Input Voltage VAC:90V to 305V; No. of Outputs:1; Output Voltage Nom.:24V; Output Current Max:2.1A; Output Power Max:50W; Depth:39mm; Width:68mm ;RoHS Compliant: Yes |
| DLG50PS36 | 制造商:XP Power 功能描述:LED DRIVER AC-DC 50W 制造商:XP Power 功能描述:LED DRIVER, AC-DC, 50W 制造商:XP Power 功能描述:LED DRIVER, 36VDC, 50W; Applications:Lighting; Power Supply Output Type:Fixed; Input Voltage VAC:90V to 305V; No. of Outputs:1; Output Voltage Nom.:36V; Output Current Max:1.4A; Output Power Max:50W; Depth:39mm; Width:68mm ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。