參數資料
型號： DM6382F
廠商： Electronic Theatre Controls, Inc.
英文描述： V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
中文描述： .34綜合數據/傳真/語音/揚聲器調制解調器設備集
文件頁數： 18/40頁
文件大小： 341K
代理商： DM6382F
DM336P
V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
18
Final
Version: DM336P-DS-F02
August 15, 2000
There are two other special considerations for
software protocol. During an iteration, it is possible
that the 55H and AAH combination is never detected.
It is also possible that the checksum does not match.
If either of these cases occurs on the first iteration, it
must be assumed that the READ_DATA port is in
conflict. If a conflict is detected, then the
READ_DATA port will be relocated. The above
process is repeated until a non-conflicting location for
the READ_DATA port is found. The entire range
between 203H and 3FFH is available; however, in
practice, it is expected that only a few locations will be
tried before software determines that no Plug and
Play cards are present.
During subsequent iterations, the occurrence of either
of these two special cases should be interpreted as
the absence of any further Plug and Play cards (i.e.
the last card was found in the previous iteration). This
terminates the isolation protocol.
Note: The software must delay 1 msec prior to
starting the first pair of isolation reads, and wait
250 msec between each sub-sequence pair of
isolation reads. This delay gives the ISA card
time to access information from very slow
storage devices.
(8) Plug and Play Isolation Sequence
The Plug and Play isolation sequence is divided into four states: Wait for Key, Sleep, Isolation, and Configuration.
The state transitions for the Plug and Play ISA card are shown below:
POWER UP
RETDRV OR
RESET COMMAND
WAIT FOR KEY
STATE
ACTIVE COMMANDS
NO ACTIVE
COMMANDS
SLEEP
STATE
ACTIVE COMMANDS
RESET
RESET CSN
WAIT FOR KEY
WAKE(CSN)
ISOLATION
STATE
ACTIVE COMMANDS
RESET
RESET CSN
WAIT FOR KEY
SET RD_DATA PORT
SERIAL ISOLATION
WAKE(CSN)
SET CSN
CONFIG
STATE
ACTIVE COMMANDS
RESET
RESET CSN
WAIT FOR KEY
WAKE(CSN)
RESOURCE DATA
STATUS
LOGICAL DIVICE
I/O RANGE CHECK
ACTIVATE
CONFIGURATION REGISTERS
SET CSN
WAKE=0 & CSN=0
WAKE<>CSN
WAKE<>0 & WAKE=CSN
LOSE SERIAL ISOLATION OR
WAKE<>CSN
Note:
1. CSN = Card Select Number.
2. RSTDRV causes a state transition from the current state to Wait for Key and sets all CSNs to zero.
3. The Wait for Key command causes a state transition from the current state to Wait for Key.
4. The Reset CSN commands include PnP Reset CSN and DM Reset CSN commands.
The former sets all ISA PnP cards CSNs to zero, while the latter only sets DM6383 PnP cards
CSNs to zero. command will cause a state transition.
Plug and Play ISA Card State Transitions
相關PDF資料
PDF描述
DM6383F V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
DM336P V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
DM64ALS244BN Dual 4-Bit Non-Inverting Buffer/Driver
DM74ALS32MX Quad 2-input OR Gate
DM74ALS5245-1WM Single 8-bit Bus Transceiver
相關代理商/技術參數
參數描述
DM6383F 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
DM63G 制造商:American Electronic Components / DURAKOOL 功能描述:Relay Socket Module 制造商:American Electronic Components / DURAKOOL 功能描述:RELAY SOCKET MODULE; Socket Mounting:Plug In; Voltage Rating:230V; Accessory Type:Relay Socket; Contact Voltage AC Max:230V; Contact Voltage DC Max:230V; Features:Green LED; For Use With:DZM2, DZM4, DZM90 & DZM92 Relays ;RoHS Compliant: Yes
DM644 LL-SUB-12-1F 制造商:Timesys Corporation 功能描述:LINUXLINK PRO EDITION FOR TI DAVINCI DM644X - Virtual or Non-Physical Inventory (Software & Literature)
DM6441ZWTARCL 制造商:Texas Instruments 功能描述:
DM644X FREE-12-1F 制造商:Timesys Corporation 功能描述:LINUXLINK FREE EDITION FOR TI DAVINCI DM644X - Virtual or Non-Physical Inventory (Software & Literature)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*