- 您現在的位置：買賣IC網 > PDF目錄376777 > DM74123 (Fairchild Semiconductor Corporation) Dual Retriggerable One-Shot with Clear and Complementary Outputs PDF資料下載
參數資料
| 型號： | DM74123 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Dual Retriggerable One-Shot with Clear and Complementary Outputs |
| 中文描述： | 雙可重觸發一桿的清除和互補輸出 |
| 文件頁數： | 2/5頁 |
| 文件大?。?/td> | 56K |
| 代理商： | DM74123 |
www.fairchildsemi.com
2
D
Operating Rules
1. An external resistor (R
X
) and external capacitor (C
X
)
are required for proper operation. The value of C
X
may
vary from 0 to any necessary value. For small time con-
stants high-grade mica, glass, polypropylene, polycar-
bonate, or polystyrene material capacitors may be
used. For large time constants use tantalum or special
aluminum capacitors. If the timing capacitors have
leakages approaching 100 nA or if stray capacitance
from either terminal to ground is greater than 50 pF the
timing equations may not represent the pulse width the
device generates.
2. When an electrolytic capacitor is used for C
X
a switch-
ing diode is often required for standard TTL one-shots
to prevent high inverse leakage current (Figure 1).
However, its use in general is not recommended with
retriggerable operation.
3. The output pulse width (T
W
) for C
X
>
1000 pF is
defined as follows:
T
W
=
K R
X
C
X
(1
+
0.7/R
X
)
1. where: [R
X
is in Kilo-ohm]
[C
X
is in pico Farad]
[T
W
is in nano second]
[K
≈
0.28]
FIGURE 1.
4.
For C
X
<
1000 pF see Figure 2 for T
W
vs. C
X
family curves with R
X
as a parameter:
Pulse Width vs. R
X
and C
X
FIGURE 2.
5.
To obtain variable pulse width by remote trim-
ming, the following circuit is recommended:
Note:
“R
remote
” should be as close to the one-shot as possible.
FIGURE 3.
6.
The retriggerable pulse width is calculated as
shown below:
T
=
T
W
+
t
PLH
=
K
×
R
X
×
C
X
+
t
PLH
The retriggered pulse width is equal to the
pulse width plus a delay time period (Figure
4).
FIGURE 4.
7.
Under any operating condition C
X
and R
X
must be kept as close to the one-shot device
pins as possible to minimize stray capaci-
tance, to reduce noise pick-up, and to reduce
I
×
R and Ldi/dt voltage developed along their
connecting paths. If the lead length from C
X
to
pins (6) and (7) or pins (14) and (15) is greater
than 3 cm, for example, the output pulse width
might be quite different from values predicted
from the appropriate equations. A non-induc-
tive and low capacitive path is necessary to
ensure complete discharge of C
X
in each
cycle of its operation so that the output pulse
width will be accurate.
V
CC
and ground wiring should conform to
good high-frequency standards and practices
so that switching transients on the V
CC
and
ground return leads do not cause interaction
between one-shots. A 0.01
μ
F to 0.10
μ
F
bypass capacitor (disk ceramic or monolithic
type) from V
CC
to ground is necessary on
each device. Furthermore, the bypass capaci-
tor should be located as close to the V
CC
pin
as space permits.
8.
Note:
For further detailed device characteristics and output performance
please refer to the One-Shot Application Note, AN-366.
相關PDF資料 |
PDF描述 |
|---|---|
| DM74123N | Dual Retriggerable One-Shot with Clear and Complementary Outputs |
| DM74145 | BCD to Decimal Decoders/Drivers |
| DM74145N | BCD to Decimal Decoders/Drivers |
| DM7414 | hex inverter with schmitt trigger input |
| DM7414N | Hex Inverter with Schmitt Trigger Input |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DM74123J/A+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Monostable Multivibrator |
| DM74123N | 功能描述:單穩態多諧振蕩器 Dual Retrig One Shot RoHS:否 制造商:Texas Instruments 每芯片元件:1 邏輯系列:LVC 邏輯類型:Monostable Multivibrator 封裝 / 箱體:SSOP-8 傳播延遲時間:18.6 ns 高電平輸出電流:- 32 mA 低電平輸出電流:32 mA 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| DM74123N/A+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Monostable Multivibrator |
| DM74123N/B+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Monostable Multivibrator |
| DM74125 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Quad TRI-STATE Buffers |
發布緊急采購，3分鐘左右您將得到回復。