參數資料
型號： DM9102A
廠商： Electronic Theatre Controls, Inc.
英文描述： Single Chip Fast Ethernet NIC controller
中文描述： 單芯片快速以太網網卡控制器
文件頁數： 9/77頁
文件大?。?/td> 459K
代理商： DM9102A
DM9102A
Single Chip Fast Ethernet NIC controller
the WOL as pulse or DC signal.
0 = WOL pulse mode (default)
1 = WOL DC mode
BPAD2 is also a reset latch pin. It is Boot ROM address and
data bus when normal operation. When at power on reset, it is
used to pull up or down externally through a resister to select
the PME as pulse or DC signal.
0 = PME pulse mode (default)
1 = PME DC mode
BPAD7 is also a reset latch pin. It is Boot ROM address and
data bus when normal operation. When at power on reset, it is
used to pull up or down externally through a resister to select
LED mode.
0 = LED mode 0 (default)
1 = LED mode 1
72
BPCS#
O
Boot ROM Chip Select
Boot ROM or external register chip select signal.
73
BPA0/WMODE
O, LI
Boot ROM address line/WOL mode selection
This multiplexed pin acts as boot ROM address bit 0 output
signal during normal operation. When at power on reset, it
used to select the type of WOL signal.
0 = WOL high active (default)
1 = WOL low active
74
BPA1/PCIMODE#
I/O, LI Boot ROM address line / PCI mode selection
This multiplexed pin acts as the boot ROM address bit 1 output
signal during normal operation. When RST# is active (low), it
acts as the input system type. If the DM9102A is used in a
CardBus system, this pin should be connected to a pull-up
resistor; otherwise, the DM9102A consider the host as a PCI
system.
0 = PCI mode (default)
1 = CardBus mode
77
EEDI
I
EEPROM Data In
The DM9102A will read the contents of EEPROM serially
through this pin.
78
EEDO
O
EEPROM Data Out
The DM9102A will use this pin to serially write opcodes,
addresses and data into the EEPROM.
79
EECK
O
EEPROM Serial Clock
This pin provides the clock for the EEPROM data transfer.
80
EECS
O
EEPROM Chip Select
This pin will enable the EEPROM during loading of the
Configuration Data.
81
SELROM
I
Multiplex or Director mode selection
0 = Multiplex mode (default)
1 = Direct mode
83,84,85,91,92,93,94
NC
NC
In Multiplex mode, these pins are not connected.
Final
Version: DM9102A-DS-F03
August 28, 2000
9
相關PDF資料
PDF描述
DM9102AF Single Chip Fast Ethernet NIC controller
DM9102AT Single Chip Fast Ethernet NIC controller
DM9108APPLICATIONENGINEERINGNOTESONE DM9108 Application Engineering notes one
DM9108APPLICATIONENGINEERINGNOTESTHREE DM9108 Application Engineering notes three
DM9108APPLICATIONENGINEERINGNOTESTWO DM9108 Application Engineering notes two
相關代理商/技術參數
參數描述
DM9102AF 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single Chip Fast Ethernet NIC controller
DM9102AT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single Chip Fast Ethernet NIC controller
DM9102D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE CHIP FAST ETHEMET NIC CONTROLLER
DM9102DE 制造商:DAVICOM 制造商全稱:DAVICOM 功能描述:Single Chip Fast Ethernet NIC Controller
DM9102DEP 制造商:DAVICOM 功能描述:IC ENET CNTRL 10/100M PHY 1 制造商:DAVICOM 功能描述:IC ENET CNTRL 10/100M PHY 128LQFP 制造商:DAVICOM 功能描述:IC, ENET CNTRL, 10/100M PHY, 128LQFP 制造商:DAVICOM 功能描述:IC, ENET CNTRL, 10/100M PHY, 128LQFP; Data Rate:100Mbps; Ethernet Type:IEEE 802.3u; Supply Voltage Min:2.375V; Supply Voltage Max:2.625V; Digital IC Case Style:LQFP; No. of Pins:128; Interface Type:PCI; Operating Temperature Min:0C;;RoHS Compliant: Yes
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*