參數資料
型號： DRV8800PWPR
廠商： TEXAS INSTRUMENTS INC
元件分類： 運動控制電子
英文描述： BRUSH DC MOTOR CONTROLLER, 2.8 A, PDSO16
封裝： PLASTIC, HTSSOP-16
文件頁數： 4/27頁
文件大?。?/td> 952K
代理商： DRV8800PWPR
SLVS855E – JULY 2008 – REVISED OCTOBER 2010
www.ti.com
Charge Pump
The charge pump is used to generate a supply above VBB to drive the source-side DMOS gates. A 0.1-mF
ceramic monolithic capacitor should be connected between CP1 and CP2 for pumping purposes. A 0.1-mF
ceramic monolithic capacitor, CStorage, should be connected between VCP and VBB to act as a reservoir to run
the high-side DMOS devices. The VCP voltage level is internally monitored and, in the case of a fault condition,
the outputs of the device are disabled.
Shutdown
As a measure to protect the device, faults caused by very high junction temperatures or low voltage on VCP
disable the outputs of the device until the fault condition is removed. At power on, the UVLO circuit disables the
drivers.
Low-Power Mode
Control input nSLEEP is used to minimize power consumption when the DRV8800/DRV8801 is not in use. This
disables much of the internal circuitry, including the internal voltage rails and charge pump. nSLEEP is asserted
low. A logic high on this input pin results in normal operation. When switching from low to high, the user should
allow a 1-ms delay before applying PWM signals. This time is needed for the charge pump to stabilize.
MODE 1 (MODE on the DRV8800)
Input MODE 1 is used to toggle between fast-decay mode and slow-decay mode. A logic high puts the device
in slow-decay mode.
MODE 2 (DRV8801 only)
MODE 2 is used to select which set of drivers (high side versus low side) is used during the slow-decay
recirculation. MODE 2 is meaningful only when MODE 1 is asserted high. A logic high on MODE 2 has
current recirculation through the high-side drivers. A logic low has current recirculation through the low-side
drivers.
Braking
The braking function is implemented by driving the device in slow-decay mode (MODE 1 pin is high) and
deasserting the enable to low. Because it is possible to drive current in both directions through the DMOS
switches, this configuration effectively shorts out the motor-generated BEMF as long as the ENABLE chop mode
is asserted. The maximum current can be approximated by VBEMF/RL. Care should be taken to ensure that the
maximum ratings of the device are not exceeded in worse-case braking situations – high-speed and high-inertia
loads.
Diagnostic Output
The nFAULT pin signals a problem with the chip via an open-drain output. A motor fault, undervoltage condition,
or TJ > 160°C drives the pin active low. This output is not valid when nSLEEP puts the device into minimum
power dissipation mode (i.e., nSLEEP is low). nFAULT stays asserted (nFAULT = L) until VBB reaches VBBNFR
to give the charge pump headroom to reach its undervoltage threshold. nFAULT is a status-only signal and does
not affect any device functionality. The H-bridge portion still operates normally down to VBB = 8 V with nFAULT
asserted.
Thermal Shutdown (TSD)
Two die-temperature monitors are integrated on the chip. As die temperature increases toward the maximum, a
thermal warning signal is triggered at 160°C. This fault drives the nFAULT low, but does not disable the
operation of the chip. If the die temperature increases further, to approximately 175°C, the full-bridge outputs are
disabled until the internal temperature falls below a hysteresis of 15°C.
12
Copyright 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): DRV8800 DRV8801
相關PDF資料
PDF描述
DRW16 ROTARY CODED SWITCH-16POSITIONS, HEXADECIMAL, LATCHED, THROUGH HOLE-STRAIGHT
5-1437584-7 ROTARY CODED SWITCH-16POSITIONS, HEXADECIMAL, LATCHED, THROUGH HOLE-STRAIGHT
DS-1177 Power Dividers Space Qualified
DS-1178 Power Dividers Space Qualified
DS-117 Three-Way Power Dividers 1300 MHz
相關代理商/技術參數
參數描述
DRV8800RTYR 功能描述:馬達/運動/點火控制器和驅動器 Full Bridge Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
DRV8800RTYT 功能描述:馬達/運動/點火控制器和驅動器 Full Bridge Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
DRV8801 制造商:TI 制造商全稱:Texas Instruments 功能描述:DMOS FULL-BRIDGE MOTOR DRIVERS
DRV8801A0RTY 制造商:TI 制造商全稱:Texas Instruments 功能描述:DMOS FULL-BRIDGE MOTOR DRIVERS
DRV8801AQRMJRQ1 功能描述:Bipolar Motor Driver DMOS Parallel 16-WQFN (4x4) 制造商:texas instruments 系列:汽車級，AEC-Q100 包裝:剪切帶（CT） 零件狀態:有效 電機類型 - 步進:雙極性 電機類型 - AC，DC:有刷直流 功能:驅動器 - 全集成，控制和功率級 輸出配置:半橋（2） 接口:并聯 技術:DMOS 步進分辨率:- 應用:通用 電流 - 輸出:2.8A 電壓 - 電源:6.5 V ~ 36 V 電壓 - 負載:6.5 V ~ 36 V 工作溫度:-40°C ~ 150°C（TJ） 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商器件封裝:16-WQFN（4x4） 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*