參數資料
型號: DRV8825PWP
廠商: TEXAS INSTRUMENTS INC
元件分類: 運動控制電子
英文描述: BRUSH DC MOTOR CONTROLLER, PDSO28
封裝: GREEN, PLASTIC, HTSSOP-28
文件頁數: 22/22頁
文件大小: 628K
代理商: DRV8825PWP
I
=
CHOP
V
REFX
5
RISENSE
SLVSA73C
– APRIL 2010 – REVISED MAY 2011
Current Regulation
The current through the motor windings is regulated by a fixed-frequency PWM current regulation, or current
chopping. When an H-bridge is enabled, current rises through the winding at a rate dependent on the DC voltage
and inductance of the winding. Once the current hits the current chopping threshold, the bridge disables the
current until the beginning of the next PWM cycle.
In stepping motors, current regulation is used to vary the current in the two windings in a semi-sinusoidal fashion
to provide smooth motion.
The PWM chopping current is set by a comparator which compares the voltage across a current sense resistor
connected to the xISEN pins, multiplied by a factor of 5, with a reference voltage. The reference voltage is input
from the xVREF pins.
The full-scale (100%) chopping current is calculated in Equation 1.
(1)
Example:
If a 0.25-
sense resistor is used and the VREFx pin is 2.5 V, the full-scale (100%) chopping current will be
2.5 V / (5 x 0.25
) = 2 A.
The reference voltage is scaled by an internal DAC that allows fractional stepping of a bipolar stepper motor, as
described in the microstepping indexer section below.
Decay Mode
During PWM current chopping, the H-bridge is enabled to drive current through the motor winding until the PWM
current chopping threshold is reached. This is shown in Figure 3 as case 1. The current flow direction shown
indicates positive current flow.
Once the chopping current threshold is reached, the H-bridge can operate in two different states, fast decay or
slow decay.
In fast decay mode, once the PWM chopping current level has been reached, the H-bridge reverses state to
allow winding current to flow in a reverse direction. As the winding current approaches zero, the bridge is
disabled to prevent any reverse current flow. Fast decay mode is shown in Figure 3 as case 2.
In slow decay mode, winding current is re-circulated by enabling both of the low-side FETs in the bridge. This is
shown in Figure 3 as case 3.
Figure 3. Decay Mode
Copyright
2010–2011, Texas Instruments Incorporated
9
相關PDF資料
PDF描述
DRW10CRA ROTARY CODED SWITCH-10POSITIONS, BCD COMPLEMENT, LATCHED, 0.02A, 20VDC, THROUGH HOLE-RIGHT ANGLE
DRW10 ROTARY CODED SWITCH-10POSITIONS, BINARY CODED DECIMAL, LATCHED, THROUGH HOLE-STRAIGHT
DS-808-4 Broadband Eight-Way Power Divider 20 - 2000 MHz
DS0012 MALE, D SUBMINIATURE CONNECTOR, SURFACE MOUNT, PLUG; RECEPTACLE
DS00196-MT221-7F 9 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, SURFACE MOUNT
相關代理商/技術參數
參數描述
DRV8825PWPR 功能描述:馬達/運動/點火控制器和驅動器 2.5A Bipolar Stepper Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
DRV8828EVM 功能描述:電源管理IC開發工具 DRV8828 Eval mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
DRV8828PWP 功能描述:馬達/運動/點火控制器和驅動器 H-Bridge motor controller IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
DRV8828PWPR 功能描述:馬達/運動/點火控制器和驅動器 H-Bridge motor controller IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
DRV8829EVM 功能描述:電源管理IC開發工具 DRV8829 Eval mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V