參數資料
型號: DS1050P-5/T&R
廠商: Maxim Integrated Products
文件頁數: 10/17頁
文件大小: 0K
描述: IC PWM 5-BIT 5KHZ 2-WIRE 8-USOP
標準包裝: 3,000
類型: 脈寬調制器(PWM)
PLL: 無
電路數: 1
比率 - 輸入:輸出: 2:1
差分 - 輸入:輸出: 無/無
頻率 - 最大: 5kHz
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-uMAX
包裝: 帶卷 (TR)
DS1050
2 of 17
OPERATION
Interface protocol is simplified to an 8-bit control byte and 8-bit data byte. Information can be read or
written to the DS1050 including a commanded shutdown operation.
Power-Up Configuration
The DS1050 powers-up to half-scale (10000B) providing 50% duty-cycle. In this mode, the DS1050 can
be used as a standalone oscillator of the frequency specified. Once powered, the PWM output can be
changed via the 2-wire addressable serial port.
Pin Description
Vcc – Power supply terminal. The DS1050 will support operation from power supply voltages ranging
from +2.7 volts to +5.5 volts.
GND – Ground terminal.
PWMO – Pulse-width modulated output. This output is a square-wave having amplitudes from 0 volts to
VCC. The duty cycle of this output is governed by a 5-bit control register. Output duty cycles range from
0% to 96.88%. An additional command sequence will provide a 100% duty cycle or “full-on.”
SCL – Serial clock input.
SDA – Serial bi-directional data I/O.
A0, A1, A2 – Device address (chip selects).
2-Wire Addressable Serial Port Control
The 2-wire serial port interface supports a bi-directional data transmission protocol with device
addressing. A device that sends data on the bus is defined as a transmitter, and a device receiving data as
a receiver. The device that controls the message is called a “master.” The devices that are controlled by
the master are “slaves.” The bus must be controlled by a master device that generates the serial clock
(SCL), controls the bus access, and generates the START and STOP conditions. The DS1050 operates as
a slave on the 2-wire bus. Connections to the bus are made via the open-drain I/O lines SDA and SCL.
The following I/O terminals control the 2-wire serial port: SDA, SCL, A0, A1, and A2. A 2-wire serial
port overview and timing diagrams for the 2-wire serial port can be found in Figures 2 and 5,
respectively. Timing information for the 2-wire serial port is provided in the “AC Electrical
Characteristics” table for 2-wire serial communications.
相關PDF資料
PDF描述
VI-2NN-IW-B1 CONVERTER MOD DC/DC 18.5V 100W
DS1050P-1/T&R IC PWM 5-BIT 1KHZ 2-WIRE 8-USOP
VI-2NM-IW-B1 CONVERTER MOD DC/DC 10V 100W
DS1050P-10/T&R IC PWM 5-BIT 10KHZ 2-WIRE 8-USOP
VI-2NL-IW-B1 CONVERTER MOD DC/DC 28V 100W
相關代理商/技術參數
參數描述
DS1050U-001 功能描述:電壓模式 PWM 控制器 5 Bit 118-mil 2-Wire 1kHz PWM RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
DS1050U-001/T&R 制造商:Maxim Integrated Products 功能描述:PROGRAM PWM 8P USOP 1KHZ 2-W T&R - Tape and Reel
DS1050U-001/T&R 功能描述:電壓模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
DS1050U-001+ 功能描述:電壓模式 PWM 控制器 5 Bit 118-mil 2-Wire 1kHz PWM RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
DS1050U-001+T 功能描述:電壓模式 PWM 控制器 5 Bit 118-mil 2-Wire 1kHz PWM RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel