- 您現在的位置：買賣IC網 > PDF目錄9570 > DS1050Z-025+ (Maxim Integrated Products)IC PWM 5BIT 25KHZ 2-WIRE 8SOIC PDF資料下載
參數資料
| 型號： | DS1050Z-025+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 12/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PWM 5BIT 25KHZ 2-WIRE 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 類型： | 脈寬調制器（PWM） |
| PLL： | 無 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 2:1 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 25kHz |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC（窄型） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁
DS1050
4 of 17
The master device generates all serial clock pulses and the START and STOP conditions. A transfer is
ended with a STOP condition or with a repeated START condition. Since a repeated START condition is
also the beginning of the next serial transfer, the bus will not be released.
The DS1050 may operate in the following two modes:
1. Slave receiver mode: Serial data and clock are received through SDA and SCL, respectively. After
each byte is received, an acknowledge bit is transmitted. START and STOP conditions are recognized
as the beginning and end of a serial transfer. Address recognition is performed by hardware after
reception of the slave (device) address and direction bit.
2. Slave transmitter mode: The first byte is received and handled as in the slave receiver mode.
However, in this mode the direction bit will indicate that the transfer direction is reversed. Serial data
is transmitted on SDA by the DS1050 while the serial clock is input on SCL. START and STOP
conditions are recognized as the beginning and end of a serial transfer.
SLAVE ADDRESS
A command/control byte is the first byte received following the START condition from the master
device. The command/control byte consists of a four-bit control code. For the DS1050, this is set as 0101
binary for read/write operations. The next three bits of the command/control byte are the device select
bits or slave address (A2, A1, A0). They are used by the master device to select which of eight possible
devices is to be accessed. When reading or writing the DS1050, the device select bits must match the
device select pins (A2, A1, A0). The last bit of the command/control byte (R/W) defines the operation to
be performed. When set to a one a read operation is selected, and when set to a zero a write operation is
selected. The command control byte is presented in Figure 3.
Following the START condition, the DS1050 monitors the SDA bus checking the device type identifier
being transmitted. Upon receiving the 0101 control code, the appropriate device address bits, and the
read/write bit, the slave device outputs an “acknowledge” signal on the SDA line.
COMMAND AND PROTOCOL
The command and protocol structure of the DS1050 allows the user to read or write the PWM
configuration register or place the device in a low-current state (shut-down mode) and recall the device
from a low-current state. Additionally, the 2-wire command/protocol structure of the DS1050 will support
eight different devices that can be uniquely controlled.
Figure 4a, b, c, d, & e show the five different command and protocol bytes for the DS1050. These include
the following command operations: 1) Set PWM duty cycle, 2) Set PWM duty cycle 100%, 3) Set
shutdown mode, 4) Set recall mode, 5) Read PWM configuration register.
The command operation “Set PWM Duty Cycle” is used to configure the output duty cycle of the device.
The DS1050 has a 5-bit resolution and is capable of setting the duty cycle output from 0% up to 96.88%
in steps of 3.125%. A binary value of (00000B) sets the duty cycle output at 0% while a binary value of
(11111B) sets the duty cycle output at 96.88%.
The command operation “Set PWM Duty Cycle 100%” is used to configure the output duty cycle of the
device to a “full-on.” This command is provided in addition to the Set PWM Duty Cycle command for
flexibility and convenience in total duty cycle coverage. It allows the user to provide a total duty cycle
range from 0% to 100%.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX232EWE | IC 2DVR/2RCVR RS232 5V 16-SOIC |
| DS1050Z-005+ | IC PWM 5BIT 5KHZ 2-WIRE 8SOIC |
| MAX232EPE | IC 2DVR/2RCVR RS232 5V 16-DIP |
| DS1050U-025+ | IC PWM 5BIT 25KHZ 2-WIRE 8USOP |
| MAX231EPD | IC 2DVR/2RCVR RS232 5V 14-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1050Z-025/T&R | 制造商:Maxim Integrated Products 功能描述:PROG PWM 8P SOIC 25KHZ 2-W T&R - Tape and Reel |
| DS1050Z-025/T&R | 功能描述:電壓模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| DS1050Z-025/W | 功能描述:電壓模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| DS1050Z-025+ | 功能描述:電壓模式 PWM 控制器 5 Bit 150-mil 2-Wire 25kHz PWM RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| DS1050Z-025+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:PULSE WIDTH MODULATOR 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC PWM 5BIT 25KHZ 2-WIRE 8SOIC |
發布緊急采購，3分鐘左右您將得到回復。