- 您現在的位置：買賣IC網 > PDF目錄299010 > DS1231S-35 Power Supply Supervisor PDF資料下載
參數資料
| 型號： | DS1231S-35 |
| 英文描述： | Power Supply Supervisor |
| 中文描述： | 電源監控 |
| 文件頁數： | 2/9頁 |
| 文件大?。?/td> | 66K |
| 代理商： | DS1231S-35 |
DS1231/S
022698 2/9
OPERATION
The DS1231 Power Monitor detects out-of-tolerance
power supply conditions and warns a processor-based
system of impending power failure. The main elements
of the DS1231 are illustrated in Figure 1. As shown, the
DS1231 actually has two comparators, one for monitor-
ing the input (Pin 1) and one for monitoring VCC (Pin 8).
The VCC comparator outputs the signals RST (Pin 5)
and RST (Pin 6) when VCC falls below a preset trip level
as defined by TOL (Pin 3).
When TOL is connected to ground, the RST and RST
signals will become active as VCC goes below 4.75
volts. When TOL is connected to VCC, the RST and RST
signals become active as VCC goes below 4.5 volts. The
RST and RST signals are excellent control signals for a
microprocessor, as processing is stopped at the last
possible moments of valid VCC. On power-up, RST and
RST are kept active for a minimum of 150 ms to allow the
power supply to stabilize (see Figure 2).
The comparator monitoring the input pin produces the
NMI signal (Pin 7) when the input threshold voltage
(VTP) falls to a level as determined by Mode (Pin 2).
When the Mode pin is connected to VCC, detection oc-
curs at VTP-. In this mode Pin 1 is an extremely high im-
pedance input allowing for a simple resistor voltage di-
vider network to interface with high voltage signals.
When the Mode pin is connected to ground, detection
occurs at VTP+. In this mode Pin 1 sources 30 A of cur-
rent allowing for connection to switched inputs, such as
a UL-approved opto-isolator. The flexibility of the input
pin allows for detection of power loss at the earliest point
in a power supply system, maximizing the amount of
time allotted between NMI and RST. On power-up, NMI
is released as soon as the input threshold voltage (VTP)
is achieved and VCC is within nominal limits. In both
modes of operation the input pin has hysteresis for
noise immunity (Figure 3).
APPLICATION – MODE PIN
CONNECTED TO VCC
When the Mode pin is connected to VCC, pin 1 is a high
impedance input. The voltage sense point and the level
of voltage at the sense point are dependent upon the
application (Figure 4). The sense point may be devel-
oped from the AC power line by rectifying and filtering
the AC. Alternatively, a DC voltage level may be se-
lected which is closer to the AC power input than the
regulated +5-volt supply, so that ample time is provided
for warning before regulation is lost.
Proper operation of the DS1231 requires a maximum
voltage of 5 volts at the input (Pin 1), which must be
derived from the maximum voltage at the sense point.
This is accomplished with a simple voltage divider net-
work of R1 and R2. Since the IN trip point VTP- is 2.3
volts (using the -20 device), and the maximum allowable
voltage on pin 1 is 5 volts, the dynamic range of voltage
at the sense point is set by the ratio of 2.3/5.0=.46 min.
This ratio determines the maximum deviation between
the maximum voltage at the sense point and the actual
voltage which will generate NMI.
Having established the desired ratio, and confirming
that the ratio is greater than .46 and less than 1, the
proper values for R1 and R2 can be determined by the
equation as shown in Figure 4. A simple approach to
solving this equation is to select a value for R2 which is
high enough impedance to keep power consumption
low, and solve for R1. Figure 5 illustrates how the
DS1231 can be interfaced to the AC power line when
the mode pin is connected to VCC.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1231S-50 | Power Supply Supervisor |
| DS1241 | Peripheral IC |
| DS1241N | Peripheral IC |
| DS1241Q | Peripheral IC |
| DS1241QN | Peripheral IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1231S-35/T&R | 制造商:Maxim Integrated Products 功能描述:POWER MONITOR-35-16PIN-SOIC-TRL - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:IC POWER MONITOR 35NS 16-SOIC 制造商:Maxim Integrated Products 功能描述:Supervisory Circuits Power Monitor |
| DS1231S-35/T&R | 功能描述:監控電路 Power Monitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1231S-35+ | 功能描述:監控電路 Power Monitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1231S-35+T&R | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 4.62V 2000UA 16SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POWER MONITOR 35NS 16-SOIC 制造商:Maxim Integrated Products 功能描述:Supervisory Circuits Power Monitor |
| DS1231S-35+T&R | 功能描述:監控電路 Power Monitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。