- 您現在的位置：買賣IC網 > PDF目錄376949 > DS1259S Battery Management PDF資料下載
參數資料
| 型號： | DS1259S |
| 英文描述： | Battery Management |
| 中文描述： | 電池管理 |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 189K |
| 代理商： | DS1259S |
DS1250Y/AB
7 of 11
POWER-DOWN/POWER-UP TIMING
(t
A
: See Note 10)
PARAMETER
SYMBOL
t
PD
V
CC
slew from V
TP
to 0V
t
F
V
CC
TP
t
R
t
REC
MIN
0
TYP
MAX
UNITS
NOTES
11
CE
,
WE
at V
IH
before Power-Down
s
300
300
2
s
s
CE
,
WE
at V
IH
after Power-Up
125
ms
(t
A
=25 C)
PARAMETER
SYMBOL
Expected Data Retention Time
t
DR
MIN
10
TYP
MAX
UNITS
years
NOTES
9
WARNING:
Under no circumstance are negative undershoots, of any amplitude, allowed when device is in battery
backup mode.
NOTES:
1.
WE
is high for a Read Cycle.
2.
OE
= V
IH
or V
IL
. If
OE
= V
IH
during write cycle, the output buffers remain in a high-impedance state.
3.
t
WP
is specified as the logical AND of
CE
and
WE
. t
WP
is measured from the latter of
CE
or
WE
going low to the earlier of
CE
or
WE
going high.
4.
t
DH
, t
DS
are measured from the earlier of
CE
or
WE
going high.
5.
These parameters are sampled with a 5 pF load and are not 100% tested.
6.
If the
CE
low transition occurs simultaneously with or latter than the
WE
low transition, the output
buffers remain in a high-impedance state during this period.
7.
If the
CE
high transition occurs prior to or simultaneously with the
WE
high transition, the output
buffers remain in high-impedance state during this period.
8.
If
WE
is low or the
WE
low transition occurs prior to or simultaneously with the
CE
low transition,
the output buffers remain in a high-impedance state during this period.
9.
Each DS1250 has a built-in switch that disconnects the lithium source until V
CC
is first applied by the
user. The expected t
DR
is defined as accumulative time in the absence of V
CC
starting from the time
power is first applied by the user.
10.
All AC and DC electrical characteristics are valid over the full operating temperature range. For
commercial products, this range is 0 C to 70 C. For industrial products (IND), this range is -40 C to
+85 C.
11.
In a power-down condition the voltage on any pin may not exceed the voltage on V
CC
.
12.
t
WR1
and t
DH1
are measured from
WE
going high.
13.
t
WR2
and t
DH2
are measured from
CE
going high.
14.
DS1250 DIP modules are recognized by Underwriters Laboratory (U.L. ) under file E99151.
DS1250 PowerCap modules are pending U.L. review. Contact the factory for status.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1259SN | Battery Management |
| DS1250BL | 4096K Nonvolatile SRAM |
| DS1260-100 | Smart Battery |
| DS1260 | Smart Battery |
| DS1260-25 | Smart Battery |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1259S/T&R | 制造商:Maxim Integrated Products 功能描述:IC BATTERY MANAGER IND 16-SOIC |
| DS1259S/T&R | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| DS1259S/T&R/C01 | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| DS1259S/T&R/C02 | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| DS1259S/T&R/C03 | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。