- 您現在的位置：買賣IC網 > PDF目錄9328 > DS1286 (Maxim Integrated Products)IC TIMEKEEPER WATCHDOG 28-EDIP PDF資料下載
參數資料
| 型號： | DS1286 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 16/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TIMEKEEPER WATCHDOG 28-EDIP |
| 標準包裝： | 12 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，方波輸出，SRAM，監視計時器 |
| 存儲容量： | 50B |
| 時間格式： | HH:MM:SS:hh（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | 并聯 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電壓 - 電源，電池： | 2.4 V ~ 3.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 28-DIP 模塊（0.61"，15.49mm）23 引線 |
| 供應商設備封裝： | 28-EDIP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁
DS1284/DS1286
7 of 18
WATCHDOG ALARM REGISTERS
Registers C and D contain the time for the watchdog alarm. The two registers contain a time count from
to 99.99 seconds in BCD. The value written into the watchdog alarm registers can be written or read in
any order. Any access to Registers C or D causes the watchdog alarm to reinitialize and clears the
watchdog flag bit and the watchdog interrupt output. When a new value is entered or the watchdog
registers are read, the watchdog timer starts counting down from the entered value to 0. When 0 is
reached, the watchdog interrupt output goes to the active state. The watchdog timer countdown is
interrupted and reinitialized back to the entered value every time either of the registers is accessed. In this
manner, controlled periodic accesses to the watchdog timer can prevent the watchdog alarm from ever
going to an active level. If access does not occur, the countdown alarm is repetitive. The watchdog alarm
registers always read the entered value. The actual countdown register is internal and is not readable.
Writing Registers C and D to 0 disables the watchdog alarm feature.
COMMAND REGISTER (0Bh)
Bit #:
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Name:
TE
IPSW
IBH
PU/LVL
WAM
TDM
WAF
TDF
Note: The initial state of these bits is not defined.
Bit 7: Transfer Enable (TE). This bit when set to logic 1 allows the internal time and date counters to
update the user accessible registers. When set to logic 0, the external, user-accessible time and date
registers remain static when being read or written, while the internal counters continue to run. The
function of this bit is further described in the time-of-day registers section
Bit 6: Interrupt Pin Swap (IPSW). This bit directs which type of interrupt is present on interrupt pins
INTA or INTB (INTB). When set to logic 1, INTA becomes the time-of-day alarm interrupt pin and
INTB (INTB) becomes the watchdog interrupt pin. When bit 6 is set to logic 0, the interrupt functions are
reversed such that the time-of-day alarm is output on
INTB (INTB) and the watchdog interrupt is output
on
INTA. Caution should be exercised when dynamically setting this bit as the interrupts are reversed
even if in an active state.
Bit 5: Interrupt B Active High/Low (IBH). When bit 5 is set to logic 1, the B interrupt output sources
current when active. When bit 5 is set to logic 0, the B interrupt output sinks current when active.
Bit 4: Pulse/Level Output (PU/LVL). When set to logic 1, the pulse mode is selected and
INTA sinks
current for a minimum of 3ms and then releases. Output
INTB (INTB) either sinks or sources current for
a minimum of 3ms depending on the level of bit 5. The watchdog timer continues to run and WAF is
cleared at the end of the pulse. When set to a logic 0, both
INTA and INTB (INTB), when active, output
an active low (
INTB (INTB) active high when IBH = 1) until the interrupt is cleared.
Bit 3: Watchdog Alarm Mask (WAM). When this bit is written to logic 1, the watchdog interrupt
output is deactivated regardless of the state of WAF. When WAM is set to logic 0 and the WAF bit is set
to a 1, the watchdog interrupt output goes to the active state, which is determined by bits 1, 4, 5, and 6 of
the command register.
Bit 2: Time-of-Day Alarm Mask (TDM). When this bit is written to logic 1, the time-of-day alarm-
interrupt output is deactivated regardless of the state of TDF. When TDM is set to logic 0, the time-of-day
相關PDF資料 |
PDF描述 |
|---|---|
| MCP4262-502E/MF | IC POT DGTL DUAL 5K RHEO 10DFN |
| MCP4261-104E/ML | IC POT DGTL DUAL 100K SPI 16QFN |
| MS3450L18-13PZ | CONN RCPT 4POS WALL MNT W/PINS |
| MCP4261-503E/ML | IC POT DGTL DUAL 50K SPI 16QFN |
| DS1643-100 | IC RAM TIMEKEEP NV 100NS 28-EDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1286+ | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1286I | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1286I+ | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS12885 | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS12885+ | 功能描述:實時時鐘 RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。