- 您現在的位置：買賣IC網 > PDF目錄376951 > DS1321 Flexible Nonvolatile Controller with Lithium Battery Monitor PDF資料下載
參數資料
| 型號： | DS1321 |
| 英文描述： | Flexible Nonvolatile Controller with Lithium Battery Monitor |
| 中文描述： | 靈活的非易失控制器，帶有鋰電池 |
| 文件頁數： | 4/12頁 |
| 文件大?。?/td> | 220K |
| 代理商： | DS1321 |
DS1321
4 of 12
BATTERY VOLTAGE MONITORING
The DS1321 automatically performs periodic battery voltage monitoring at a factory-programmed time
interval of 24 hours. Such monitoring begins within t
REC
after V
CCI
rises above V
CCTP
and is suspended
when power failure occurs.
After each 24-hour period (t
BTCN
) has elapsed, the DS1321 connects V
BAT
to an internal 1 M
=
test
resistor (R
INT
) for one second (t
BTPW
). During this one second, if V
BAT
falls below the factory-
programmed battery voltage trip point (V
BTP
), the battery warning output
BW
is asserted. While
BW
is
active, battery testing will be performed with period t
BTCW
to detect battery removal and replacement.
Once asserted,
BW
remains active until the battery is physically removed and replaced by a fresh cell.
The battery is still retested after each V
CC
power-up, however, even if
BW
was active on power-down. If
the battery is found to be higher than V
BTP
during such testing,
BW
is deasserted and regular 24-hour
testing resumes.
BW
has an open-drain output driver.
Battery replacement following
BW
activation is normally done with V
CCI
nominal so that SRAM data is
not lost. During battery replacement, the minimum time duration between old battery detachment and
new battery attachment (t
BDBA
) must be met or
BW
will not deactivate following attachment of the new
battery. Should
BW
not deactivate for this reason, the new battery can be detached for t
BDBA
and then re-
attached to clear
BW
.
NOTE: The DS1321 cannot constantly monitor an attached battery because such monitoring would
drastically reduce the life of the battery. As a result, the DS1321 only tests the battery for one second out
of every 24 hours and does not monitor the battery in any way between tests. If a good battery (one that
has not been previously flagged with
BW
) is removed between battery tests, the DS1321 may not
immediately sense the removal and may not activate
BW
until the next scheduled battery test. If a battery
is then reattached to the DS1321, the battery may not be tested until the next scheduled test.
NOTE: Battery monitoring is only a useful technique when testing can be done regularly over the entire
life of a lithium battery. Because the DS1321 only performs battery monitoring when V
CC
is nominal,
systems which are powered-down for excessively long periods can completely drain their lithium cells
without receiving any advanced warning. To prevent such an occurrence, systems using the DS1321
battery monitoring feature should be powered-up periodically (at least once every few months) in order to
perform battery testing. Furthermore, anytime
BW
is activated on the first battery test after a power-up,
data integrity should be checked via checksum or other technique.
POWER MONITORING
The DS1321 automatically detects out-of-tolerance power supply conditions and warns a processor-based
system of impending power failure. When V
CCI
falls below the trip point level defined by the TOL pin
(V
CCTP
), the V
CCI
comparator activates the reset signal
RST
. Reset occurs in the range of 4.75 to 4.5 volts
(5% tolerance) when the TOL pin is connected to GND or in the range of 4.5 to 4.25 volts (10%
tolerance) when TOL is connected to V
CCO
.
RST
also serves as a power-on reset during power-up. After V
CCI
exceeds V
CCTP
,
RST
will be held active
for 200 ms nominal (t
RPU
). This reset period is sufficiently long to prevent system operation during
power-on transients and to allow t
REC
to expire.
RST
has an open-drain output driver.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1330AB | 256k Nonvolatile SRAM with Battery Monitor |
| DS1330YP-100-IND | Isolation Transformer |
| DS1330ABP-100 | 256k Nonvolatile SRAM with Battery Monitor |
| DS1330ABP-100-IND | 256k Nonvolatile SRAM with Battery Monitor |
| DS1330ABP-70 | 256k Nonvolatile SRAM with Battery Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1321_04 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Flexible Nonvolatile Controller with Lithium Battery Monitor |
| DS1321+ | 功能描述:存儲器控制器 Flexible NV Cntlr w/Lithium Battery RoHS:否 制造商:Maxim Integrated |
| DS1321E | 功能描述:IC CTRL NV W/BATT MON 5V 20TSSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 - 控制器 系列:- 標準包裝:45 系列:- 控制器類型:靜態 RAM（SRAM） 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC W 包裝:管件 |
| DS1321E/T&R | 制造商:Maxim Integrated Products 功能描述:NV CONTRL 5V X4 BW&RST 20-TSSOP T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CTRL NV W/BATT MON 5V 20TSSOP |
| DS1321E/T&R | 功能描述:IC CTRL NV W/BATT MON 5V 20TSSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 - 控制器 系列:- 標準包裝:45 系列:- 控制器類型:靜態 RAM（SRAM） 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC W 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。