參數資料
型號: DS1337S
英文描述: Serial Real-Time Clock
中文描述: 串行實時時鐘
文件頁數: 12/13頁
文件大?。?/td> 364K
代理商: DS1337S
DS1337
Figure 4. Data Transfer On 2-Wire Serial Bus
12 of 13
Depending upon the state of the R/
W
bit, two types of data transfer are possible:
1)
Data transfer from a master transmitter to a slave receiver.
The first byte transmitted by the
master is the slave address. Next follows a number of data bytes. The slave returns an acknowledge
bit after each received byte. Data is transferred with the most significant bit (MSB) first.
2)
Data transfer from a slave transmitter to a master receiver.
The master transmits the first byte
(the slave address). The slave then returns an acknowledge bit, followed by the slave transmitting a
number of data bytes. The master returns an acknowledge bit after all received bytes other than the
last byte. At the end of the last received byte, a “not acknowledge” is returned. The master device
generates all of the serial clock pulses and the START and STOP conditions. A transfer is ended with
a STOP condition or with a repeated START condition. Since a repeated START condition is also the
beginning of the next serial transfer, the bus is not released. Data is transferred with the most
significant bit (MSB) first.
The DS1337 can operate in the following two modes:
1)
Slave Receiver Mode (Write Mode):
Serial data and clock are received through SDA and SCL.
After each byte is received an acknowledge bit is transmitted. START and STOP conditions are
recognized as the beginning and end of a serial transfer. Address recognition is performed by
hardware after reception of the slave address and direction bit (Figure 5). The slave address byte is
the first byte received after the master generates the START condition. The slave address byte
contains the 7-bit DS1337 address, which is 1101000, followed by the direction bit (R/
W
), which, for
a write, is 0. After receiving and decoding the slave address byte the device outputs an acknowledge
on the SDA line. After the DS1337 acknowledges the slave address + write bit, the master transmits a
word address to the DS1337. This sets the register pointer on the DS1337. The master may then
transmit 0 or more bytes of data, with the DS1337 acknowledging each byte received. The master
generates a STOP condition to terminate the data write.
2)
Slave Transmitter Mode (Read Mode):
The first byte is received and handled as in the slave
receiver mode. However, in this mode, the direction bit indicates that the transfer direction is
reversed. Serial data is transmitted on SDA by the DS1337 while the serial clock is input on SCL.
相關PDF資料
PDF描述
DS1337U Serial Real-Time Clock
DS1339 Serial Real-Time Clock
DS1339C-3 I2C Serial Real-Time Clock
DS1339C-33 TRANS NPN 160V 350MW SMD SOT-23
DS1339U-2 Serial Real-Time Clock
相關代理商/技術參數
參數描述
DS1337S/T&R 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RTC SERIAL 2WIRE LP 8-SOIC 制造商:Maxim Integrated Products 功能描述:Real Time Clock I2C Serial RTC
DS1337S/T&R 功能描述:實時時鐘 I2C Serial RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1337S+ 功能描述:實時時鐘 I2C Serial RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1337S+ 制造商:Maxim Integrated Products 功能描述:IC SEMICONDUCTOR ((NS))
DS1337S+C01 功能描述:IC RTC SERIAL 2WIRE LP 8-SOIC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器,閏年,SRAM 存儲容量:- 時間格式:HH:MM:SS(12/24 小時) 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源,電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件