- 您現在的位置：買賣IC網 > PDF目錄9361 > DS1344E-3+ (Maxim Integrated Products)IC RTC SPI 3.0V 20TSSOP PDF資料下載
參數資料
| 型號： | DS1344E-3+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC SPI 3.0V 20TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 74 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，NVRAM，方波輸出，涓流充電器 |
| 存儲容量： | 96B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | SPI |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 管件 |
14
Maxim Integrated
Low-Current SPI/3-Wire RTCs
DS1343/DS1344
Status Register (10h)
Trickle Charger Register (11h)
Register 11h controls the devices’ trickle-charge char-
acteristics. The simplified schematic of Figure 2 shows
the basic components of the trickle charger. The trickle-
charge select (TCS[3:0]) bits (bits 7:4) control the
selection of the trickle charger. To prevent accidental
enabling, only a pattern of 1010 enables the trickle
charger; all other patterns disable the trickle charger.
On the initial application of power, the devices power
up with the trickle charger disabled. The diode-select
(DS[1:0]) bits (bits 3:2) select whether or not a diode is
connected between VCC and VBAT. The resistor-select
(RS[1:0]) bits (bits 1:0) select the resistor that is con-
nected between VCC and VBAT. The RS and DS bits
select the resistor and diodes, as shown in Table 3. The
user determines diode and resistor selection according
to the maximum current desired for secondary battery or
super cap charging. The maximum charging current can
be calculated using the equation that follows.
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
OSF
0
IRQF1
IRQF0
1
0
BIT 7
OSF: Oscillator stop flag. If the OSF bit is 1, the oscillator either has stopped or was stopped for some period
and could be used to judge the validity of the clock and calendar data. This bit is edge triggered and is set to
1 when the internal circuitry senses the oscillator has transitioned from a normal run state to a stop condition.
This bit remains at logic 1 until written to logic 0. Attempting to write OSF to 1 leaves the value unchanged.
The following are examples of conditions that can cause the OSF bit to be set:
1) The first time power is applied.
2) The voltage present on VCC is insufficient to support oscillation.
3) The EOSC bit is a logic one during battery backup.
4) External influences on the crystal (i.e., noise, leakage, etc.).
BIT 1
IRQF1: Interrupt request 1 flag. A logic 1 in the IRQF1 bit indicates that the time matched the Alarm 1 reg-
isters. This flag can be used to generate an interrupt on either INT0 or INT1 depending on the status of the
INTCN bit in the Control register. If the INTCN bit is 0 and IRQF1 is 1 (and the A1IE bit is also 1), INT0 goes
low. If the INTCN bit is 1 and IRQF1 is 1 (and the A1IE bit is also 1), INT1 goes low. IRQF1 is cleared when
the address pointer is set to any of the Alarm 1 registers during an I/O transaction. The IRQF1 bit can also
be cleared by writing it to 0. This bit can only be written to 0. Attempting to write the IRQF1 bit to 1 leaves the
value unchanged.
BIT 0
IRQF0: Interrupt request 0 flag. A logic 1 in the IRQF0 bit indicates that the time matched the Alarm 0 regis-
ters. If the A0IE bit is also 1, INT0 goes low. IRQF0 is cleared when the address pointer is set to any of the
Alarm 0 registers during an I/O transaction. The IRQF0 bit can also be cleared by writing it to 0. This bit can
only be written to 0. Attempting to write the IRQF0 bit to 1 leaves the value unchanged.
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
TCS3
TCS2
TCS1
TCS0
DS1
DS0
RS1
RS0
0
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5403EUB+ | IC DGTL POT DUAL 256-TAP 10-UMAX |
| VI-2NZ-MW-F3 | CONVERTER MOD DC/DC 2V 40W |
| VI-26B-MX-B1 | CONVERTER MOD DC/DC 95V 75W |
| VI-2NZ-MW-F2 | CONVERTER MOD DC/DC 2V 40W |
| VI-26B-MW | CONVERTER MOD DC/DC 95V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1344E-3+ | 功能描述:實時時鐘 Low-Current SPI/3-Wire RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1344E-3+T&R | 制造商:Maxim Integrated Products 功能描述:SPI RTC 20P TSSOP 3V 12.5PF AM T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RTC SPI 3.0V 20TSSOP |
| DS1344E-3+T&R | 功能描述:實時時鐘 Low-Current SPI/3-Wire RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1344E-33+ | 功能描述:實時時鐘 Low-Current SPI/3-Wire RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1344E-33+T&R | 制造商:Maxim Integrated Products 功能描述:SPI RTC 20P TSSOP 3.3V 12.5PF A T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RTC SPI 3.3V 20TSSOP 制造商:Maxim Integrated Products 功能描述:Real Time Clock Low-Current SPI/3-Wire RTC |
發布緊急采購，3分鐘左右您將得到回復。