- 您現在的位置：買賣IC網 > PDF目錄1994 > DS1486P-120+ (Maxim Integrated Products)IC TIMEKEEPER RAM 1MB 34-PCM PDF資料下載
參數資料
| 型號： | DS1486P-120+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/14頁 |
| 文件大小： | 0K |
| 描述： | IC TIMEKEEPER RAM 1MB 34-PCM |
| 標準包裝： | 40 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，NVSRAM，方波輸出，監視計時器 |
| 存儲容量： | 128KB |
| 時間格式： | HH:MM:SS:hh（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | 并聯 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電壓 - 電源，電池： | 3.3V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 34-PowerCap? 模塊 |
| 供應商設備封裝： | 34-PowerCap 模塊 |
| 包裝： | 管件 |
DS1486/DS1486P
6 of 14
TIME-OF-DAY REGISTERS
Registers 0, 1, 2, 4, 6, 8, 9, and A contain Time-of-Day data in BCD. Ten bits within these eight registers
are not used and will always read 0 regardless of how they are written. Bits 6 and 7 in the Months
Register (9) are binary bits. When set to logic 0,
EOSC (Bit 7) enables the real-time clock oscillator. This
bit is set to logic 1 as shipped from Dallas Semiconductor to prevent lithium energy consumption during
storage and shipment (DIP Module only). This bit will normally be turned on by the user during device
initialization. However, the oscillator can be turned on and off as necessary by setting this bit to the
appropriate level. The
INTA and Square Wave Output signals are tied together at pin 30 on the 32-pin
DIP module. With this package,
ESQW (Bit 6) of the Months Register (9) controls the function of this
pin. When set to logic 0, the pin will output a 1024 Hz square wave signal. When set to logic 1, the pin is
available for interrupt A output (
INTA) only. The INTA and Square Wave Output signals are separated
on the 34-pin PowerCap module. With this package,
ESQW controls only the Square Wave Output (pin
33). When set to logic 0, pin 33 will output a 1024 Hz square wave signal. When set to logic 1, pin 33 is
in a high impedance state. Pin 34 (
INTA) is not affected by the setting of bit 6. Bit 6 of the Hours register
is defined as the 12- or 24-hour select bit. When set to logic 1, the 12-hour format is selected. In the 12-
hour format, bit 5 is the AM/PM bit with logic 1 being PM. In the 24-hour mode, bit 5 is the second 10-
hour bit (20-23 hours). The Time-of-Day registers are updated every 0.01 seconds from the real-time
clock, except when the TE bit (bit 7 of Register B) is set low or the clock oscillator is not running. The
preferred method of synchronizing data access to and from the RAMified Timekeeper is to access the
Command register by doing a write cycle to address location B and setting the TE bit (Transfer Enable
bit) to a logic 0. This will freeze the External Time-of-Day registers at the present recorded time,
allowing access to occur without danger of simultaneous update. When the watch registers have been read
or written, a second write cycle to location B setting the TE bit to a logic 1 will put the Time-of-Day
Registers back to being updated every 0.01 second. No time is lost in the real-time clock because the
internal copy of the Time-of-Day register buffers is continually incremented while the external memory
registers are frozen. An alternate method of reading and writing the Time-of-Day registers is to ignore
synchronization. However, any single reading may give erroneous data as the real-time clock may be in
the process of updating the external memory registers as data is being read. The internal copies of seconds
through years are incremented and the Time-of-Day Alarm is checked during the period that hundreds of
seconds reads 99. The copies are transferred to the external register when hundredths of seconds roll from
99 to 00. A way of making sure data is valid is to do multiple reads and compare. Writing the registers
can also produce erroneous results for the same reasons. A way of making sure that the write cycle has
caused a proper update is to perform read verifies and re-execute the write cycle if data is not correct.
While the possibility of erroneous results from read and write cycles has been stated, it is worth noting
that the probability of an incorrect result is kept to a minimum due to the redundant structure of the
RAMified Timekeeper.
TIME-OF-DAY ALARM REGISTERS
Registers 3, 5, and 7 contain the Time-of-Day Alarm Registers. Bits 3, 4, 5, and 6 of Register 7 will
always read 0 regardless of how they are written. Bit 7 of Registers 3, 5, and 7 are mask bits (Figure 3).
When all of the mask bits are logic 0, a Time-of-Day Alarm will only occur when Registers 2, 4, and 6
match the values stored in Registers 3, 5, and 7. An alarm will be generated every day when bit 7 of
Register 7 is set to a logic 1. Similarly, an alarm is generated every hour when bit 7 of Registers 7 and 5
is set to a logic 1. When bit 7 of Registers 7, 5, and 3 is set to a logic 1, an alarm will occur every minute
when Register 1 (seconds) rolls from 59 to 00.
Time-of-Day Alarm Registers are written and read in the same format as the Time-of-Day Registers. The
Time-of-Day Alarm Flag and Interrupt are always cleared when Alarm Registers are read or written.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1500WE | IC RTC Y2KC W/NV CTRL 32-TSOP |
| DS1501YSN+T&R | IC RTC WDOG Y2K 5V IND 28-SOIC |
| DS1553P-70+ | IC RTC RAM Y2K 5V 70NS 34-PCM |
| DS1554W-120IND | IC RTC RAM Y2K 3.3V 120NS 32EDIP |
| DS1556WP-120IND | IC RTC RAM Y2K 3.3V 120NS 34PCM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1486P-120+ | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1486P-150 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:RAMified Watchdog Timekeeper |
| DS1487 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Low Power RS-485 1⁄4 Unit Load Multipoint Transceiver |
| DS1487M | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| DS1487M/NOPB | 功能描述:RS-422/RS-485 接口 IC LO PR RS485/1/4 UNIT LOAD MULTIPT XCVR RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。