- 您現在的位置：買賣IC網 > PDF目錄1994 > DS1603+ (Maxim Integrated Products)IC COUNTER ELAPSED TIME 5V 7-SIP PDF資料下載
參數資料
| 型號： | DS1603+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/9頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COUNTER ELAPSED TIME 5V 7-SIP |
| 標準包裝： | 1 |
| 類型： | 耗用時間計數器 |
| 時間格式： | 二進制 |
| 數據格式： | 二進制 |
| 接口： | 3 線串口 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電壓 - 電源，電池： | 3 V ~ 4.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 14-DIP 模塊（0.335"，8.51mm） |
| 供應商設備封裝： | 14-EDIP |
| 包裝： | 托盤 |
DS1603
3 of 9
DATA INPUT
Following the 8-bit protocol that inputs write mode, 32 bits of data are written to the selected counter on
the rising edge of the next 32 CLK cycles. After 32 bits have been entered any additional CLK cycles will
be ignored until RST is transitioned low to end data transfer and then high again to begin new data
transfer.
DATA OUTPUT
Following the eight CLK cycles that input read mode protocol, 32 bits of data will be output from the
selected counter on the next 32 CLK cycles. The first data bit to be transmitted from the selected 32-bit
counter occurs on the falling edge after the last bit of protocol is written. When transmitting data from the
selected 32-bit counter, RST must remain at high level as a transition to low level will terminate data
transfer. Data is driven out the DQ pin as long as CLK is low. When CLK is high the DQ pin is tristated.
OSCILLATOR OUTPUT
Pin 6 of the DS1603 module is a 1Hz output signal. This signal is present only when VCC is applied and
greater than the internal power supply. However, the output is guaranteed to meet TTL requirement only
while VCC is within normal limits. This output can be used as a 1-second interrupt or time tick needed in
some applications.
INTERNAL POWER
The internal battery of the DS1603 module provides 35mAh and will run the elapsed time counter for
over 10 years in the absence of power.
PIN DESCRIPTIONS
VCC, GND – DC power is provided to the device on these pins. VCC is the +5V input. When 5V is applied
within normal limits, the device is fully accessible and data can be written and read. When a 3V battery is
connected to the device and VCC is below 1.25 x VBAT, reads and writes are inhibited. As VCC falls below
VBAT the continuous counter is switched over to the internal battery.
CLK (Serial Clock Input) – CLK is used to synchronize data movement on the serial interface.
DQ (Data Input/Output) – The DQ pin is the bi-directional data pin for the 3-wire interface.
RST (Reset) – The reset signal must be asserted high during a read or a write.
OSC (One Hertz Output Signal) – This signal is only present when Vcc is at a valid level and the
oscillator is enabled.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1642-70+ | IC RAM TIMEKEEP NV 70NS 24-EDIP |
| DS1643P-70+ | IC RAM TIMEKEEP NV 70NS 34-PCM |
| DS1644P-120 | IC RAM TIMEKEEP NV 120NS 34-PCM |
| DS1646-120+ | IC RAM TIMEKEEP NV 120NS 32-EDIP |
| DS1647P-120 | IC RAM TIMEKEEP NV 120NS 34-PCM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1603+ | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1603J | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:TRI-STATE Dual Receiver |
| DS1603J/883 | 制造商:National Semiconductor Corporation 功能描述:Dual Receiver 14-Pin CDIP |
| DS1603N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Timer Circuit |
| DS16-03P | 制造商:Cooper Bussmann 功能描述:TOP SCREW-ON INSERTION BRIDGE, 3 POLE, F - Bulk 制造商:COOPER BUSSMANN 功能描述:TOP SCREW-ON INSERTION BRIDGE, 3 POLE, F |
發布緊急采購，3分鐘左右您將得到回復。