- 您現在的位置：買賣IC網 > PDF目錄9361 > DS17285S-5+T&R (Maxim Integrated Products)IC RTC 5V 2K NV RAM 24-SOIC PDF資料下載
參數資料
| 型號： | DS17285S-5+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/31頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC 5V 2K NV RAM 24-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，夏令時，閏年，NVSRAM，方波輸出 |
| 存儲容量： | 2KB |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | 并聯 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電壓 - 電源，電池： | 2.5 V ~ 3.7 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
DS17285/DS17287/DS17485/DS17487/DS17885/DS17887
Nonvolatile RAM
The user RAM bytes are not dedicated to any special
function within the DS17x85. They can be used by the
processor program as battery-backed memory and are
fully available during the update cycle.
The user RAM is divided into two separate memory
banks. When the bank 0 is selected, the 14 real-time
clock registers and 114 bytes of user RAM are accessi-
ble. When bank 1 is selected, an additional 2kbytes,
4kbytes, or 8kbytes of user RAM are accessible
through the extended RAM address and data registers.
Interrupts
The RTC includes six separate, fully automatic sources
of interrupt for a processor:
1) Alarm Interrupt
2) Periodic Interrupt
3) Update-Ended Interrupt
4) Wake-Up Interrupt
5) Kickstart Interrupt
6) RAM Clear Interrupt
The conditions that generate each of these indepen-
dent interrupt conditions are described in detail in other
sections of this data sheet. This section describes the
overall control of the interrupts.
The application software can select which interrupts, if
any, are to be used. There are 6 bits, including 3 bits in
Register B and 3 bits in Extended Register 4B, that
enable the interrupts. The extended register locations
are described later. Writing logic 1 to an interrupt-
enable bit permits that interrupt to be initiated when the
event occurs. A logic 0 in the interrupt-enable bit pro-
hibits the IRQ pin from being asserted from that interrupt
condition. If an interrupt flag is already set when an
interrupt is enabled, IRQ is immediately set at an active
level, although the event initiating the interrupt condition
might have occurred much earlier. Therefore, there are
cases where the software should clear these earlier
generated interrupts before first enabling new interrupts.
When an interrupt event occurs, the relating flag bit is
set to logic 1 in Register C or in Extended Register 4A.
These flag bits are set regardless of the setting of the
corresponding enable bit located either in Register B or
in Extended Register 4B. The flag bits can be used in a
polling mode without enabling the corresponding
enable bits.
However, care should be taken when using the flag bits
of Register C as they are automatically cleared to 0
immediately after they are read. Double latching is
implemented on these bits so that set bits remain sta-
ble throughout the read cycle. All bits that were set are
cleared when read and new interrupts that are pending
during the read cycle are held until after the cycle is
completed. One, two, or three bits can be set when
reading Register C. Each used flag bit should be exam-
ined when read to ensure that no interrupts are lost.
The flag bits in Extended Register 4A are not automati-
cally cleared following a read. Instead, each flag bit
can be cleared to 0 only by writing 0 to that bit.
When using the flag bits with fully enabled interrupts,
the IRQ line is driven low when an interrupt flag bit is
set and its corresponding enable bit is also set. IRQ is
held low as long as at least one of the six possible
interrupt sources has its flag and enable bits both set.
The IRQF bit in Register C is 1 whenever the IRQ pin is
being driven low as a result of one of the six possible
active sources. Therefore, determination that the
DS17x85/DS17x87 initiated an interrupt is accom-
plished by reading Register C and finding IRQF = 1.
IRQF remains set until all enabled interrupt flag bits are
cleared to 0.
Oscillator Control Bits
A pattern of 01X in bits 4 to 6 of Register A turns the
oscillator on and enables the countdown chain. A pat-
tern of 11X (DV2 = 1, DV1 = 1, DV0 = X) turns the oscil-
lator on, but holds the countdown chain of the oscillator
in reset. All other combinations of bits 4 to 6 keep the
oscillator off.
When the DS17x87 is shipped from the factory, the
internal oscillator is turned off. This feature prevents the
lithium energy cell from being used until it is installed in
a system.
Square-Wave Output Selection
Thirteen of the 15 divider taps are made available to a
1-of-16 multiplexer, as shown in Figure 1. The square
wave and periodic interrupt generators share the out-
put of the multiplexer. The RS0–RS3 bits in Register A
establish the output frequency of the multiplexer. These
frequencies are listed in Table 4. Once the frequency is
selected, the output of the SQW pin can be turned on
and off under program control with the square-wave
enable bit (SQWE).
If E32K = 0, the square-wave output is determined by
the RS3 to RS0 bits. If E32K = 1, a 32kHz square wave
is output on the SQW pin, regardless of the RS3 to RS0
bits’ state. If E32K = ABE = 1 and a valid voltage is
applied to VBAUX, a 32kHz square wave is output on
SQW when VCC is below VTP.
Real-Time Clocks
18
____________________________________________________________________
相關PDF資料 |
PDF描述 |
|---|---|
| VI-26K-MW | CONVERTER MOD DC/DC 40V 100W |
| VI-2NZ-MW-F4 | CONVERTER MOD DC/DC 2V 40W |
| DS17285S-3+T&R | IC RTC 3V 2K NV RAM 24-SOIC |
| VI-26J-MX-B1 | CONVERTER MOD DC/DC 36V 75W |
| DS1302S-16/T&R | IC TIMEKEEPER T-CHARGE 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS17285SN- | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Real-Time Clocks |
| DS17285SN3 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Real-Time Clocks |
| DS17285SN-3 | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17285SN-3+ | 功能描述:實時時鐘 3V/5V RTC K Multiplexed Kick-S RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17285SN5 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Real-Time Clocks |
發布緊急采購，3分鐘左右您將得到回復。