- 您現在的位置：買賣IC網 > PDF目錄9054 > DS1801S/T&R (Maxim Integrated Products)IC POT DUAL AUDIO TAPER 16-SOIC PDF資料下載
參數資料
| 型號： | DS1801S/T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DUAL AUDIO TAPER 16-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 接片： | 64 + 靜音 |
| 電阻（歐姆）： | 45k |
| 電路數： | 2 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | 3 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC W |
| 包裝： | 帶卷 (TR) |
DS1801
3 of 10
3-WIRE SERIAL INTERFACE CONTROL
Communication and control of the DS1801 is accomplished through a 3-wire serial port interface that
drives an internal control logic unit. The 3-wire serial interface is designed for microprocessor or
microcontroller applications. The interface consists of three input signals which include RST , CLK and
D.
The RST control signal is used to enable 3-wire serial port write operations. The CLK terminal is a clock
signal input that provides synchronization for data I/O while the D signal input serves to transfer
potentiometer wiper position settings to the device.
As shown in Figure 3, a 3-wire serial port operation begins with a transition of the RST signal input to a
high state. Once the 3-wire port has been activated, data is clocked into the part on the low to high
transition of the CLK signal input. Data input via the D line is transferred in the order of the desired
potentiometer-0 value followed by the potentiometer-1 value.
The DS1801 contains two 65-position potentiometers whose wiper positions are set by an 8-bit value.
These two 8-bit values are written to the 16-bit I/O shift register which is used to store wiper position
during powered conditions. Because the potentiometer has 65-positions, only 7 bits of data are needed to
set wiper position. A detailed diagram of the 16-bit I/O shift register is shown in Figure 2. Bits 0 through
7 are reserved for the potentiometer-0 control while bits 8 through 15 are reserved for control of
potentiometer-1.
Bits 0 through 5 are used for actual wiper positioning of potentiometer-0. Bit 6 is used to mute
potentiometer-0. If this bit has value 1, the potentiometer-0 wiper will be connected to the low end of the
resistive array the mute position. The value of bit 7 is a “don’t care” and will not affect operation of the
DS1801 or potentiometer-0.
Bits 8 through 13 are used for wiper positioning of potentiometer-1. Bit 14 is used for muting of the
potentiometer-1 wiper output. Bit 15, like bit 7, is a “don’t care” and will not affect operation of the
DS1801.
Data for the DS1801 is transmitted LSB first starting with bit 0. A complete transmission of 16 bits of
data is required to insure proper setting of each potentiometer’s wiper. An incomplete transmission may
result in undesired wiper settings.
Once the complete 16 bits of information has been transmitted and the RST signal input transitions to a
low state, the new wiper positions are loaded into the part.
16-BIT I/O SHIFT REGISTER Figure 2
相關PDF資料 |
PDF描述 |
|---|---|
| IDT2309B-1HPGGI8 | IC CLK BUFFER ZD HI DRV 16-TSSOP |
| IDT2309A-1HPGGI8 | IC CLK BUFFER ZD HI DRV 16-TSSOP |
| VI-B50-MY-F4 | CONVERTER MOD DC/DC 5V 50W |
| MM74HC138SJX | IC DECODER 3-8 LINE 16-SOP |
| VI-B50-MY-F3 | CONVERTER MOD DC/DC 5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1802 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1802+ | 功能描述:數字電位計 IC Dual Audio Taper Potentiometer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1802E | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1802E/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL AUDIO TAPER W/PB TSSOP T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DL AUDIO TAP W/PB 20TSSOP |
| DS1802E/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。