2) Valid for VCC = 5V o" />
參數資料
型號: DS1804UR-050
廠商: Maxim Integrated Products
文件頁數: 7/10頁
文件大?。?/td> 0K
描述: IC POT TRIM NV ROT DIE 50K 8USOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 50
接片: 100
電阻(歐姆): 50k
電路數: 1
溫度系數: 標準值 750 ppm/°C
存儲器類型: 非易失
接口: 3 線(芯片選擇,遞增,增/減)
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-uMAX
包裝: 管件
DS1804
6 of 10
NOTES:
1) All voltages are referenced to ground.
2) Valid for VCC = 5V only.
3) Resistor input voltages cannot go below ground or exceed VCC by the amounts as shown in the table.
4) Maximum current specifications are based on the clock rate of INC input. This specification
represents the current required when changing the wiper position.
5) Standby current levels apply when all inputs are driven to appropriate supply levels. CS , INC , U/ D =
VCC.
6) Wiper load time is specified as the time required for the DS1804 to load the wiper position with the
contents of nonvolatile memory once VCC has reached a stable operating voltage equal to or greater
than 2.7V.
7) The DS1804 is available in three resistor values. These include the DS1804-010, 10k
; the DS1804-
050, 50k
; and the DS1804-100, 100k.
8) Valid at TA = +25°C only.
9) Absolute linearity is used to compare measured wiper voltage versus expected wiper voltage as
determined by wiper position. The DS1804 is specified to provide an absolute linearity of ±0.60 LSB.
10) Relative linearity is used to determined the change in voltage between successive tap positions. The
DS1804 is specified to provide a relative linearity specification of ±0.25 LSB.
11) -3dB cutoff frequency characteristics for the DS1804 depend on potentiometer total resistance.
DS1804-010, 1MHz; DS1804-050, 200kHz; and DS1804-100, 100kHz.
12) Capacitance values apply at TA = +25°C.
13) See Figure 2.
14) Power-up time is specified as the time required before the three-terminal control becomes active after
a stable power supply level has been reached.
15) At VCC = 2.7V, VIL = 0.8V.
16) The INC low to CS inactive is specified to be 50ns minimum. This is the transition condition which
allows the DS1804 three-terminal port to become inactive without writing the EEPROM memory of
the part.
17) Wiper Storage Time, tWST, is the time require for the DS1804 to write EEPROM memory for storage
of a new wiper position. The maximum time required to accomplish this task is specified at 10ms.
相關PDF資料
PDF描述
IDT23S08-4DCG IC CLK MULT PLL STD DRV 16-SOIC
IDT23S08-3DCG IC CLK MULT PLL STD DRV 16-SOIC
IDT23S08-2DCG IC CLK MULT PLL STD DRV 16-SOIC
DS1845E-050 IC POT/MEM DUAL NV 50K 14-TSSOP
IDT23S08-1HDCG IC CLK MULT PLL HI DRV 16-SOIC
相關代理商/技術參數
參數描述
DS1804UR-050/T&R 制造商:Maxim Integrated Products 功能描述:IC POT TRIM NV ROT DIE 50K 8USOP
DS1804UR-050/T&R 功能描述:IC POT TRIM NV ROT DIE 50K 8USOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻(歐姆):50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型,TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR)
DS1804UR-050/T&R/ 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1804X-010 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:NV Trimmer Potentiometer
DS1804X-010/T&R 制造商:Rochester Electronics LLC 功能描述: 制造商:DSC 功能描述: