- 您現在的位置：買賣IC網 > PDF目錄1913 > DS1805E-010 (Maxim Integrated Products)IC POT DIG ADDRESS 10K 14-TSSOP PDF資料下載
參數資料
| 型號： | DS1805E-010 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/10頁 |
| 文件大小： | 0K |
| 描述： | IC POT DIG ADDRESS 10K 14-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 96 |
| 接片： | 256 |
| 電阻（歐姆）： | 10k |
| 電路數： | 1 |
| 溫度系數： | 標準值 550 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 管件 |
DS1805
Addressable Digital Potentiometer
_____________________________________________________________________
9
Following the START condition, the DS1805 monitors
the SDA bus checking the device type identifier being
transmitted. Upon receiving the 0101 address code
and appropriate device select bits, the slave device
outputs an acknowledge signal on the SDA line.
Command and Protocol
The DS1805’s command and protocol structure of the
DS1805 allows the user to read or write to both the
scratchpad and potentiometer registers. Figures 4 and
5 show the command structures for the part.
Potentiometer data values and control and command
values are always transmitted most significant bit
(MSB) first. During communications, the receiving unit
always generates the acknowledge.
Reading the DS1805
As shown in Figure 4, the DS1805 provides one read-
command operation. This operation allows the user to
read both potentiometers. Specifically, the R/W bit of the
control byte is set equal to a one for a read operation.
Communication to read the DS1805 begins with a START
condition that is issued by the master device. The control
byte from the master device follows the START condition.
Once the control byte has been received by the DS1805,
the part responds with an acknowledge. The read/write
bit of the control byte as stated should be set equal to
one for reading the DS1805.
When the master has received the acknowledge from the
DS1805, the master can then begin to receive poten-
tiometer wiper data. The value of the register-0 wiper
position will be the first returned from the DS1805. Once
the eight bits of the register-0 wiper position have been
transmitted, the master needs to issue an acknowledge,
unless it is the only byte to be read, in which case the
master issues a not acknowledge. If desired, the master
can stop the communication transfer at this point by issu-
ing the STOP condition. However, if the value of the
potentiometer-1 wiper position value is needed, commu-
nication transfer can continue by clocking the remaining
eight bits of the potentiometer-1 value, followed by a not
acknowledge. Final communication transfer is terminated
by issuing the STOP command. Figure 4 shows the flow
of the read operation.
Writing to the DS1805
Figure 5 shows a data flow diagram for writing the
DS1805. The DS1805 has three write-command opera-
tions. These include write reg-0, write pot-1, and write
reg-0/pot-1. The write reg-0 command allows the user to
write the value of scratchpad register-0 and as an option
the value of potentiometer-1. The write-1 command allows
the user to write the value of potentiometer-1 only. The
last write command, write-0/1, allows the user to write
both registers to the same value with one command and
one data value being issued.
All the write operations begin with a START condition.
Following the START condition, the master device issues
the control byte. The read/write bit of the control byte is
set to zero for writing the DS1805. Once the control byte
has been issued and the master receives the acknowl-
edgment from the DS1805, the command byte is trans-
mitted to the DS1805. As mentioned above, there exist
three write operations that can be used with the DS1805.
Figure 5 and Table 1 show the binary value of each write
command.
Figure 4. 2-Wire Read Protocols
MSB
ST
AR
T
ACK
NACK
STOP
CONTROL
BYTE
LSB
MSB
DATA
BYTE
LSB
MSB
OPTIONAL
DATA
BYTE
LSB
REG-0
POT-1
R/W = 1
0
1
0
1
A2
A1
A0
1
COMMAND
COMMAND VALUE
Write Register-0
101010 01
Write Potentiometer-1 Register
101010 10
Write Both Registers
101011 11
Table 1. 2-Wire Command Words
Package Information
For the latest package outline information, go to
www.maxim-ic.com/packages.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1806E-050/T&R | IC POT DIG SEXTET 50K 20-TSSOP |
| DS1807S/T&R | IC POT ADDRESS 2X AUDIO 16-SOIC |
| DS1808Z-050/T&R | IC POT DUAL LOG HV 50K 16-SOIC |
| DS1809U-100/T&R | IC DALLASTAT NV 100KOHM 8-USOP |
| DS1841N+ | IC RES LOG NV I2C 5.5V 10-TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1805E-010+ | 功能描述:數字電位計 IC Addressable RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1805E-010+T&R | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 256POS 10KOHM SGL 14TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DIG ADDRESS 10K 14-TSSOP 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs Addressable |
| DS1805E-010+T&R | 功能描述:數字電位計 IC Addressable RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1805E-010+T&R/W | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1805E-050 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Addressable Digital Potentiometer |
發布緊急采購，3分鐘左右您將得到回復。