- 您現在的位置：買賣IC網 > PDF目錄9168 > DS1807S+T&R (Maxim Integrated Products)IC POT ADDRESS 2X AUDIO 16-SOIC PDF資料下載
參數資料
| 型號： | DS1807S+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/13頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT ADDRESS 2X AUDIO 16-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 接片： | 64 |
| 電阻（歐姆）： | 45k |
| 電路數： | 2 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C（芯片選擇） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC W |
| 包裝： | 帶卷 (TR) |
DS1807
12 of 13
110499
NOTES:
1. All voltages are referenced to ground.
2. I/O pins of fast mode devices must not obstruct the SDA and SCL lines if VDD is switched off.
3. ICC specified with zero-crossing detection active and operating device serial port in fast mode.
4. ISTBY specified with for VCC equal 3.0V and 5.0V and SDA and SCL are driven to the appropriate
logic levels. ISTBY is specified as the current consumption of the device when SDA and SCL are in the
inactive (high) states.
5. After this period, the first clock pulse is generated.
6. A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the
VIHMIN of the SCL signal) in order to bridge the undefined region of the falling edge of SCL.
7. The maximum tHD:DAT has only to be met if the device does not stretch the LOW period (tLOW) of the
SCL signal.
8. A fast mode device can be used in a standard mode system, but the requirement tSU:DAT > 250 ns must
then be met. This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next
data bit to the SDA line tRMAX + tSU:DAT = 1000+250=1250 ns before the SCL line is released.
9. CB - total capacitance of one bus line in picofarads, timing referenced to (0.9(VCC) and (0.1)(VCC)).
10. Absolute tolerance is used to determine measured wiper voltage versus expected wiper voltage as
determined by wiper position.
11. Tap-to-tap tolerance is used to determine the change in voltage between successive tap positions. The
DS1807 is specified for a
±0.25 dB tap-to-tap tolerance.
12. Typical values are for tA = 25
°C and nominal supply voltage.
13. Address inputs, A0, A1, and A2, should be tied to either VCC or GND depending on the desired
address selections.
14. These parameters are characterized and not 100% tested.
15. Interchannel matching is used to determine the relative difference in dB between the same position on
each potentiometer. The DS1807 is specified for
±0.5 dB Interchannel matching
16. See Figure 9.
17. Valid at 25
°C only.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2WP-MY-F4 | CONVERTER MOD DC/DC 13.8V 50W |
| MS3450W24-5P | CONN RCPT 16POS WALL MNT W/PINS |
| V110A3V3H200B2 | CONVERTER MOD DC/DC 3.3V 200W |
| MS3450L24-5PZ | CONN RCPT 16POS WALL MNT W/PINS |
| VI-BWL-MV | CONVERTER MOD DC/DC 28V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1808 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Log Digital Potentiometer |
| DS1808Z-050 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1808Z-050/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL LOG HI VOLTAGE POT T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DUAL LOG HV 50K 16-SOIC |
| DS1808Z-050/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1808Z-050+ | 功能描述:數字電位計 IC Dual Log RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。