- 您現在的位置：買賣IC網 > PDF目錄1913 > DS1807S/T&R (Maxim Integrated Products)IC POT ADDRESS 2X AUDIO 16-SOIC PDF資料下載
參數資料
| 型號： | DS1807S/T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/13頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT ADDRESS 2X AUDIO 16-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 接片： | 64 |
| 電阻（歐姆）： | 45k |
| 電路數： | 2 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C（芯片選擇） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC W |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁
DS1807
7 of 13
110499
When the master has received the ACKNOWLEDGE from the DS1807, the master can then begin to
receive potentiometer wiper data. The value of the potentiometer-0 wiper position will be the first
returned from the DS1807. Once the 8 bits of the potentiometer-0 wiper position have been transmitted,
the master will need to issue an ACKNOWLEDGE, unless it is the only byte to be read, in which case the
master issues a NOT ACKNOWLEDGE. If desired the master may stop the communication transfer at
this point by issuing the STOP condition. However, if the value of the potentiometer-1 wiper position
value is needed communication transfer can continue by clocking the remaining eight bits of the
potentiometer-1 value, followed by a NOT ACKNOWLEDGE. Final communication transfer is
terminated by issuing the STOP command. Again the flow of the read operation is presented in Figure 6.
WRITING THE DS1807
A data flow diagram for writing the DS1807 is shown in Figure 7. The DS1807 has three commands
which are used to change the position(s) of the wiper. These include write pot-0, write pot-1, and write
pot-0/1. The write pot-0 command allows the user to write the value of potentiometer-0 and as an option
the value of potentiometer-1. The write-1 command allows the user to write the value of potentiometer-1
only. The last write command, write-0/1, allows the user to write both potentiometers to the same value
with one command and one data value being issued.
All the write operations begin with a START condition. Following the START condition, the master
device will issue the control byte. The read/write bit of the control byte will be set to 0 for writing the
DS1807. Once the control byte has been issued and the master receives the acknowledgment from the
DS1807, the command byte is transmitted to the DS1807. As mentioned above, there exist three write
operations that can be used with the DS1807. The binary value of each write command is shown in Figure
7 and also in Table 1.
2-WIRE WRITE COMMAND WORDS Table 1
COMMAND
COMMAND VALUE
Write Potentiometer-0
101010 01
Write Potentiometer-1
101010 10
Write Both Pots
101011 11
Once the DS1807 has received the command byte, it will responds with an ACKNOWLEDGE. The
master can then write the corresponding data-byte associated with the command byte. When the DS1807
has received the data byte(s), it will respond with an acknowledgement. At this point the master device
should respond with the STOP condition.
ZERO-CROSSING DETECTION COMMAND WORD
Zero-crossing detection was described under the operation section of this document. As stated earlier,
zero-crossing detection must be deactivated or activated under software control. The command words
used to activate or deactivate the zero-crossing detection feature is shown in Table 2.
ZERO-CROSSING DETECTION COMMAND WORDS Table 2
COMMAND
COMMAND VALUE
Activate Zero-Crossing
101111 01
Deactivate Zero-Crossing
101111 10
相關PDF資料 |
PDF描述 |
|---|---|
| DS1808Z-050/T&R | IC POT DUAL LOG HV 50K 16-SOIC |
| DS1809U-100/T&R | IC DALLASTAT NV 100KOHM 8-USOP |
| DS1841N+ | IC RES LOG NV I2C 5.5V 10-TDFN |
| DS1844S-100/T&R | IC POT DIG QUAD 100K 20-SOIC |
| DS1845E-100/T&R | IC POT/MEM DUAL NV 100K 14-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1808 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Log Digital Potentiometer |
| DS1808Z-050 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1808Z-050/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL LOG HI VOLTAGE POT T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DUAL LOG HV 50K 16-SOIC |
| DS1808Z-050/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1808Z-050+ | 功能描述:數字電位計 IC Dual Log RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。