- 您現在的位置：買賣IC網 > PDF目錄9172 > DS1808Z-050+T&R (Maxim Integrated Products)IC POT DUAL LOG HV 50K 16-SOIC PDF資料下載
參數資料
| 型號： | DS1808Z-050+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 14/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DUAL LOG HV 50K 16-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 接片： | 32 |
| 電阻（歐姆）： | 45k |
| 電路數： | 2 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 4.5 V ~ 5.5 V，±4.5 V ~ 13.2 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 帶卷 (TR) |
DS1808
6 of 17
The master device generates all serial clock pulses and the start and stop conditions. A transfer is ended
with a stop condition or with a repeated start condition. Since a repeated start condition is also the
beginning of the next serial transfer, the bus will not be released.
The DS1808 may operate in the following two modes:
1. Slave receiver mode: Serial data and clock are received through SDA and SCL respectively. After
each byte is received, an acknowledge bit is transmitted. Start and stop conditions are recognized as
the beginning and end of a serial transfer. Address recognition is performed by hardware after
reception of the slave (device) address and direction bit.
2. Slave transmitter mode: The first byte is received and handled as in the slave receiver mode.
However, in this mode the direction bit will indicate that the transfer direction is reversed. Serial data
is transmitted on SDA by the DS1808 while the serial clock is input on SCL. Start and stop conditions
are recognized as the beginning and end of a serial transfer.
3. Slave Address: command/control byte is the first byte received following the start condition from the
master device. The command/control byte consists of a 4-bit control code. For the DS1808, this is set
as 0101 binary for read/write operations. The next three bits of the command/control byte are the
device select bits or slave address (A2, A1, A0). They are used by the master device to select which
of eight devices is to be accessed. When reading or writing the DS1808, the device select bits must
match the device select pins (A2, A1, A0). The last bit of the command/control byte (R/W) defines
the operation to be performed. When set to a 1, a read operation is selected, and when set to a 0, a
write operation is selected.
Following the START condition, the DS1808 monitors the SDA bus checking the device type identifier
being transmitted. Upon receiving the 0101 control code, the appropriate device address bits, and the
read/write bit, the slave device outputs an acknowledge signal on the SDA line.
COMMAND AND PROTOCOL
The command and protocol structure of the DS1808 allows the user to read from or write to the
potentiometer(s). Additionally, the 2-wire command/protocol structure of the DS1808 will support eight
different devices and a maximum of 16 channels that can be uniquely controlled. The command
structures for the device are presented in Figures 3, 4, 5, and 6. Potentiometer data values and
command/control values are always transmitted most significant bit (MSB) first. During communications,
the receiving unit always generates the acknowledgement.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2W3-MY-F2 | CONVERTER MOD DC/DC 24V 50W |
| V72A5H300BF3 | CONVERTER MOD DC/DC 5V 300W |
| VI-2W3-MY-F1 | CONVERTER MOD DC/DC 24V 50W |
| V72A5H300BF2 | CONVERTER MOD DC/DC 5V 300W |
| DS1848B-050+ | IC RES/MEM TEMP 50/10K 16-BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1809 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dallastat, 64-position linear taper |
| DS1809-010 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1809-010+ | 功能描述:數字電位計 IC Dallastat RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1809-050 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1809-050+ | 功能描述:數字電位計 IC Dallastat RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。