- 您現在的位置：買賣IC網 > PDF目錄8604 > DS1843D+TRL (Maxim Integrated Products)IC CIRCUIT SAMPLE-N-HOLD 8-UDFN PDF資料下載
參數資料
| 型號： | DS1843D+TRL |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CIRCUIT SAMPLE-N-HOLD 8-UDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 采樣和保持 |
| 應用： | 光纖學網絡 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WFDFN |
| 供應商設備封裝： | 8-uDFN（2x2） |
| 包裝： | 帶卷 (TR) |
DS1843
Fast Sample-and-Hold Circuit
_______________________________________________________________________________________
3
Note 1: All voltages are referenced to ground. Currents entering the IC are specified positive and currents exiting the IC are negative.
Note 2: Guaranteed by design.
Note 3: VOUT at the end of the 10s hold time is within specified level of VIN during the sample window; a 50 resistor connected in
series to both VINP and VINN (VINP - VINN = 1V). External capacitance to ground for both VINP and VINN is approximately 10pF.
Note 4: The sampling capacitor must be removed from the input signal before the input signal changes. Therefore, the SEN pin
must be low for a short period of time, tDEL, before the input changes.
Note 5: VOUT at the end of the hold time is within 1% of VIN during the sample window (VINP - VINN = 1V).
Note 6: Voltage step applied across VOUTP to VOUTN through a 5pF capacitor connected to each pin. This models the load presented
by an ADC while it is sampling the DS1843’s output. See the
Output Buffer section. Settled within 1% of initial voltage.
AC ELECTRICAL CHARACTERISTICS
(VCC = +2.97V to +5.5V, TA = -40°C to +85°C, unless otherwise noted.) (See the Timing Diagram.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Sample Time Minimum
tS
VOUT is within 0.4dB (Note 3)
300
ns
Delay Time Minimum
tDEL
(Note 4)
10
ns
Output Time
tOUT
Delay from SEN falling edge until valid
output at VOUT to 1% accuracy
2
s
Hold Time
tHOLD
(Note 5)
tOUT
100
s
1V step, DEN = high
2
Output Step Recovery Time
(Note 6)
tREC
3V step, DEN = high or low
3.5
s
Timing Diagram
VINP - VINN
VOUTP - VOUTN
EXTERNAL
ADC DATA
tADC:ST = EXTERNAL ADC SAMPLING TIME.
tADC:CT = EXTERNAL ADC CONVERSION TIME.
DEN IS CONNECTED TO VCC FOR DIFFERENTIAL OUTPUT.
NOTE: THIS TIMING DIAGRAM IS APPLICABLE FOR SINGLE-ENDED AND DIFFERENTIAL OUTPUT CONFIGURATIONS.
SEN
tS
tDEL
tOUT
tADC:ST
DATA VALID
tADC:CT
tREC
tHOLD
VOLTAGE INVALID
相關PDF資料 |
PDF描述 |
|---|---|
| VI-24L-IV-F4 | CONVERTER MOD DC/DC 28V 150W |
| VI-24L-IV-F2 | CONVERTER MOD DC/DC 28V 150W |
| MAX4373HESA | IC AMP GAIN +100V/V PREC 8-SOIC |
| LTC1668CG#TR | IC DAC 16BIT 50MSPS 28SSOP |
| MAX4373FEUA | IC AMP/COMP/REF +50V/V 8-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1843K | 功能描述:放大器 IC 開發工具 Fast Sample & Hold Circuit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| DS1844 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Quad Digital Potentiometer |
| DS1844_05 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Quad Digital Potentiometer |
| DS1844-010 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1844-010+ | 功能描述:數字電位計 IC Quad RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。