- 您現在的位置：買賣IC網 > PDF目錄9535 > DS1852B-000 (Maxim Integrated Products)IC MONITOR TXRX OPTICAL 25-BGA PDF資料下載
參數資料
| 型號： | DS1852B-000 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 26/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MONITOR TXRX OPTICAL 25-BGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 640 |
| 類型： | 收發(fā)器 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 25-TFBGA，CSPBGA |
| 供應商設備封裝： | 25-BGA（5x5） |
| 包裝： | 托盤 |
DS1852
9 of 26
Write Operations
After receiving a matching address byte with the R/W bit set low, the device goes into the write mode of
operation. The master must transmit an 8-bit EEPROM memory address to the device to define the
address where the data is to be written. After the byte has been received, the DS1852 will transmit a zero
for one clock cycle to acknowledge the receipt of the address. The master must then transmit an 8-bit
data word to be written into this address. The DS1852 will again transmit a zero for one clock cycle to
acknowledge the receipt of the data. At this point the master must terminate the write operation with a
stop condition for the write to be initiated. If a start condition is sent in place of the stop condition, the
write is aborted and the data received during that operation is discarded. If the stop condition is received,
the DS1852 enters an internally timed write process (tw) to the EEPROM memory. The DS1852 will not
send an acknowledge bit for any 2-wire communication during the EEPROM write process.
The DS1852 is capable of an 8-byte page write. A page is any 8-byte block of memory starting with an
address evenly divisible by eight and ending with the starting address plus seven. For example,
addresses 00h through 07h constitute one page. Other pages would be addresses 08h through 0Fh, 10h
through 17h, 18h through 1Fh, etc.
A page write is initiated the same way as a byte write, but the master does not send a stop condition after
the first byte. Instead, after the slave has received the data byte, the master can send up to seven more
bytes using the same nine-clock sequence. The master must terminate the write cycle with a stop
condition or the data clocked into the DS1852 will not be latched into permanent memory.
The address counter rolls on a page during a write. The counter does not count through the entire
address space as during a read. For example, if the starting address is 06h and four bytes are written, the
first byte goes into address 06h. The second goes into address 07h. The third goes into address 00h (not
08h). The fourth goes into address 01h. If more than nine or more bytes are written before a stop
condition is sent, the first bytes sent are overwritten. Only the last eight bytes of data are written to the
page.
Acknowledge Polling
Once the internally timed write has started and the DS1852 inputs are disabled, acknowledge polling can
be initiated. The process involves transmitting a start condition followed by the device address. The
R/W bit signifies the type of operation that is desired. The read or write sequence will only be allowed to
proceed if the internal write cycle has completed and the DS1852 responds with a zero.
Read Operations
After receiving a matching address byte with the R/W bit set high, the device goes into the read mode of
operation. There are three read operations: current address read, random read, and sequential address
read.
CURRENT ADDRESS READ
The DS1852 has an internal address register that contains the address used during the last read or write
operation, incremented by one. This data is maintained as long as VCC is valid. If the most recent address
was the last byte in memory, then the register resets to the first address. This address stays valid between
operations as long as power is available.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-BNJ-IV-B1 | CONVERTER MOD DC/DC 36V 150W |
| GTC030A-32-10P | CONN RCPT 7POS PANEL MNT W/PINS |
| M83723/83W1412N | CONN RCPT 12POS WALL MT W/PINS |
| V24A12M300B3 | CONVERTER MOD DC/DC 12V 300W |
| V24A12M300B2 | CONVERTER MOD DC/DC 12V 300W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1852B-000/C | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| DS1852B-000/T&R | 制造商:Maxim Integrated Products 功能描述:IC MONITOR TXRX OPTICAL 25-BGA |
| DS1852B-000/T&R | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| DS1852B-000+ | 功能描述:模數轉換器 - ADC Optical Transceiver Diagnostic Monitor RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| DS1852B-000+T&R | 制造商:Maxim Integrated Products 功能描述:OPTICAL TRNSCVR 25BGA - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MONITOR TXRX OPTICAL 25-BGA 制造商:Maxim Integrated Products 功能描述:Data Converter ICs - Various Optical Transceiver Diagnostic Monitor |
發(fā)布緊急采購，3分鐘左右您將得到回復。