參數資料
型號： DS1856E-020+
廠商： Maxim Integrated Products
文件頁數： 5/31頁
文件大?。?/td> 0K
描述： IC RES TEMP-CNTRL 20/20K 16TSSOP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
接片： 256
電阻（歐姆）： 20k
電路數： 2
溫度系數： 標準值 50 ppm/°C
存儲器類型： 非易失
接口： 2 線串口
電源電壓： 2.85 V ~ 5.5 V
工作溫度： -40°C ~ 95°C
安裝類型： 表面貼裝
封裝/外殼： 16-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 16-TSSOP
包裝： 管件
Dual, Temperature-Controlled Resistors with Inter-
nally Calibrated Monitors and Password Protection
Maxim Integrated
13
DS1856
The DS1856 2-wire interface uses 8-bit addressing,
which allows up to 256 bytes to be addressed tradi-
tionally on a given 2-wire slave address. However,
since the Main Device contains more than 256 bytes, a
table scheme is used. The lower 128 bytes of the Main
Device, memory locations 00h to 7Fh, function as
expected and are independent of the currently select-
ed table. Byte 7Fh is the Table Select byte. This byte
determines which memory table will be accessed by
the 2-wire interface when address locations 80h to FFh
are accessed. Memory locations 80h to FFh are acces-
sible only through the Main Device address. The
Auxiliary Device address has no access to the tables,
but the Auxiliary Device memory can be mapped into
the Main Device’s memory space (by setting ADEN =
1). Valid values for the Table Select byte are shown in
the table below.
Before attempting to read and write any of the bits or
bytes mentioned in this section, it is important to look at
the memory map provided in a subsequent section to
verify what level of password is required. Password
protection is described in the following section.
Password Protection
The DS1856 uses two 4-byte passwords to achieve
three levels of access to various memory locations. The
three levels of access are:
User Access: This is the default state after power-up. It
allows read access to standard monitoring and status
functions.
Level 1 Access: This allows access to customer data
table (Tables 00 and 01) in addition to everything grant-
ed by User access. This level is granted by entering
Password 1 (PW1).
Level 2 Access: This allows access to all memory, set-
tings, and features, in addition to everything granted by
Level 1 and User access. This level is granted by enter-
ing Password 2 (PW2).
To obtain a particular level of access, the correspond-
ing password must be entered in the Password Entry
(PWE) bytes located in the Main Device at 7Bh to 7Eh.
The value entered is compared to both the PW1 and
PW2 settings located in Table 03, bytes B0h to B3h and
Table 03, bytes B4h to B7h, respectively, to determine
if access should be granted. Access is granted until
the password is changed or until power is cycled.
Writing PWE can be done with any level of access,
although PWE can never be read.
Writing PW1 and PW2 requires PW2 access. However,
PW1 and PW2 can never be read, even with PW2 access.
On power-up, PWE is set to all 1s (FFFFh). As long as
neither of the passwords are ever changed to FFFFh,
then User access is the power-up default. Likewise,
password protection can be intentionally disabled by
setting the PW2 password to FFFFh.
Memory Map
The following table is the legend used in the memory
map to indicate the access level required for read and
write access.
Each table in the following memory map begins with a
higher level view of a particular portion of the memory
showing information such as row (8 bytes) and byte
names. The tables are then followed, where applicable,
by an Expanded Bytes table, which shows bit names
and values. Furthermore, both tables use the permis-
sion legend to indicate the access required on a row,
byte, and bit level.
The memory map is followed by a
Register Description
section, which describes bytes and bits in further detail.
TABLE SELECT
BYTE
TABLE NAME
00
01
Auxiliary Device Memory
(When ADEN = 1)
02
Does Not Exist
03
Configuration
04
Resistor 0 Look-up Table
05
Resistor 1 Look-up Table
PERMISSION
READ
WRITE
<0>
At least one byte in the row is different than
the rest of the row, so look at each byte
separately for permissions.
<1>
all
PW2
<2>
all
NA
<3>
all
all (The part also writes to
this byte.)
<4>
PW2
PW2 + mode_bit
<5>
all
<6>
NA
all
<7>
PW1
<8>
PW2
<9>
NA
PW2
<10>
PW2
NA
<11>
all
PW1
Table 6. Table Select Byte
Table 7. Password Permission
相關PDF資料
PDF描述
DS1859E-020+ IC RES TEMP 20/20K 3MON 16-TSSOP
VI-BW2-MW-B1 CONVERTER MOD DC/DC 15V 100W
VE-2N4-MX-B1 CONVERTER MOD DC/DC 48V 75W
VI-B1W-MV CONVERTER MOD DC/DC 5.5V 150W
74LVX157MTC MULTIPLEXER QUAD 2IN LV 16TSSOP
相關代理商/技術參數
參數描述
DS1856E-020/R 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual, Temperature-Controlled Resistors with Internally Calibrated Monitors and Password Protection
DS1856E-020/T 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual, Temperature-Controlled Resistors with Internally Calibrated Monitors and Password Protection
DS1856E-020/T&R 制造商:Maxim Integrated Products 功能描述:DUAL TEMP R 20K3MONTSSOP T&R - Tape and Reel
DS1856E-020/T&R 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1856E-020+ 功能描述:數字電位計 IC Dual Temp-Controlled Resistors RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*