- 您現在的位置：買賣IC網 > PDF目錄171225 > DS1862AB+ (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY CONSUMER CIRCUIT, PBGA25 PDF資料下載
參數資料
| 型號： | DS1862AB+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PBGA25 |
| 封裝： | 5 X 5 MM, ROHS COMPLIANT, CSBGA-25 |
| 文件頁數： | 40/42頁 |
| 文件大小： | 586K |
| 代理商： | DS1862AB+ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁
DS1862A
XFP Laser Control and Digital Diagnostic IC
_______________________________________________________________________________________
7
FAST ALARMS AND VCC FAULT CHARACTERISTICS
(VCC3 = +2.9V to +5.5V, VCC2 = +1.6V to +3.6V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
HIGH BIAS and TX-P Threshold
FS
(Note 10)
2.48
2.5
2.52
mA
VCC2/3 Fault Asserted
Falling Edge Delay
VCC2/3
(Note 11)
75
ms
QT Temperature Coefficient
-3
+3
%
QT Voltage Coefficient
0.5
%/V
QT FS Trim Accuracy (4.2V,
+25°C)
2.480
2.500
2.520
mA
QT Accuracy (Trip) (INL)
-2
0
+2
LSB
QT Voltco
0.5
%/V
QT Tempco
1.5
3
%
Note 1:
All voltages are referenced to ground. Current into the IC is positive, and current out of the IC is negative.
Note 2:
Secondary power supply is used to support optional variable power-supply feature of the XFP module. If VCC2 is not used
(i.e., signal conditioners using 3.3V supply), VCC2 should be connected to the VCC3.
Note 3:
Input signals (i.e., TX-D, MOD-DESEL, and P-DOWN/RST) have internal pullup resistors.
Note 4:
Guaranteed by design. Simulated over process and 50μA < IBMD < 1500μA.
Note 5:
CB—total capacitance of one bus line in picofarads.
Note 6:
EEPROM write begins after a STOP condition occurs.
Note 7:
This is the maximum and minimum voltage on the MODSET and BIASSET pins required to meet accuracy and drift specifi-
cations.
Note 8:
For VTHRSET, offset may be as much as 10mV.
Note 9:
This is the uncalibrated offset provided by the factory; offset adjustment is available on this channel.
Note 10: %FS refers to calibrated FS in case of internal calibration, and uncalibrated FS in the case of external calibration.
Uncalibrated FS is set in the factory and specified in this data sheet as FS (factory). Calibrated FS is set by the user, allow-
ing a change in any monitored channel scale.
Note 11: See the
Monitor Channels section for more detail or VCC2 and VCC3 selection.
NONVOLATILE MEMORY CHARACTERISTICS
(VCC3 = +2.9V to +5.5V, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Endurance (Write Cycle)
+70°C
50k
Cycles
Endurance (Write Cycle)
+25°C
200k
Cycles
相關PDF資料 |
PDF描述 |
|---|---|
| DS1862AB+T&R | SPECIALTY CONSUMER CIRCUIT, PBGA25 |
| DS1868-100-IND | 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDIP14 |
| DS2-320-2AR | DIP20, IC SOCKET |
| DS1-314-1AR | DIP14, IC SOCKET |
| DS3-328-1AR | DIP28, IC SOCKET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1862AB+ | 功能描述:激光驅動器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| DS1862AB+T&R | 制造商:Maxim Integrated Products 功能描述:XFP LASER CONTROL 25CSBGA - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
| DS1862AB+T&R | 功能描述:激光驅動器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| DS1862AB+TR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:XFP Laser Control and Digital Diagnostic IC |
| DS1862B | 功能描述:激光驅動器 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。